相关实验视频

Updated: Jul 9, 2026

In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation
09:39

In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation

Published on: May 27, 2013

12.4K

半千瓦功率放大器的半千瓦功率放大器的Yb合的形双层纤维与偏振维护

Hossein Fathi, Evgenii Motorin, Ebrahim Aghayari

    Optics express
    |November 22, 2024
    PubMed
    概括

    这项研究通过直接将短脉冲放大到数百瓦的速度,使用合物合的缩双层纤维 (T-DCFs) 来推进光纤激光技术. 该系统保持高极化和光束质量,为高功率的皮秒激光器提供一个紧的解决方案.

    更多相关视频

    20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier10:17

    20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

    Published on: July 12, 2017

    11.4K
    Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy08:48

    Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy

    Published on: November 22, 2019

    7.5K

    相关概念视频

    Induced Electric Dipoles01:28

    Induced Electric Dipoles

    A permanent electric dipole orients itself along an external electric field. This rotation can be quantified by defining the potential energy because the external torque does work in rotating it. Then, the potential energy is minimum at the parallel configuration and maximum at the antiparallel configuration. While the former is a stable equilibrium, the latter is an unstable equilibrium.
    Since the absolute value of potential energy holds no physical meaning, its zero value can be chosen as per...
    Energy Stored In A Coaxial Cable01:31

    Energy Stored In A Coaxial Cable

    A coaxial cable consists of a central copper conductor used for transmitting signals, followed by an insulator shield, a metallic braided mesh that prevents signal interference, and a plastic layer that encases the entire assembly.
    In the simplest form, a coaxial cable can be represented by two long hollow concentric cylinders in which the current flows in opposite directions. The magnetic field inside and outside the coaxial cable is determined by using Ampère's law. The magnetic field inside...
    Double Resonance Techniques: Overview01:12

    Double Resonance Techniques: Overview

    Double resonance techniques in Nuclear Magnetic Resonance (NMR) spectroscopy involve the simultaneous application of two different frequencies or radiofrequency pulses to manipulate and observe two distinct nuclear spins. One important application of double resonance is spin decoupling, which selectively suppresses coupling with one type of nucleus while observing the NMR signal from another nucleus, simplifying the spectrum and enhancing resolution.
    Spin decoupling is usually achieved by...
    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    Voltage Doubler Circuit01:23

    Voltage Doubler Circuit

    A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
    BJT Amplifiers01:14

    BJT Amplifiers

    Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
    In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role extends...