相关实验视频

Updated: Jun 3, 2025

Evaluation of the Curing of Adhesive Systems by Rheological and Thermal Testing
09:06

Evaluation of the Curing of Adhesive Systems by Rheological and Thermal Testing

Published on: July 3, 2020

7.2K

功能分级粘合剂关节的评估和表征:实验和数值分析

Yanan Zhang1, Pedro Gálvez2, Miguel Angel Martínez3

  • 1Soete Laboratory, Faculty of Engineering and Architecture, Ghent University, B-9052 Ghent, Belgium.

Polymers
|January 8, 2025
PubMed
概括

这项研究表明,等级环氧粘合剂接头与单个接头相比,显著提高了剪切强度. 在SikaPower®-1548-1511-1548配置显著提高关节强度和减少应力度.

关键词:
固化过程 固化过程环氧树脂是一种环氧树脂.有限元素方法的有限元素方法.渐进的关节 渐进的关节 渐进的关节单一的膝盖关节 单一的膝盖关节

更多相关视频

Additive Manufacturing of Functionally Graded Ceramic Materials by Stereolithography06:53

Additive Manufacturing of Functionally Graded Ceramic Materials by Stereolithography

Published on: January 25, 2019

14.3K
Mechanoluminescent Visualization of Crack Propagation for Joint Evaluation04:58

Mechanoluminescent Visualization of Crack Propagation for Joint Evaluation

Published on: January 6, 2023

2.1K

相关概念视频

Method of Joints: Problem Solving II01:30

Method of Joints: Problem Solving II

Consider a truss structure with frictionless joints fixed to a wall and roller support. If a force of 150 N is applied to joint A, the forces in each member of the truss can be determined using the method of joints.
513
Bending of Members Made of Several Materials01:08

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each...
139
Method of Joints: Problem Solving I01:30

Method of Joints: Problem Solving I

The method of joints is a commonly used technique to analyze the forces in structural trusses. The method is based on the principle of equilibrium, which assumes that the truss members are connected by frictionless pins. The forces at each joint can be determined by considering the equilibrium of the forces acting on that joint. Consider a truss structure with two forces of 20 N and 10 N acting at joints C and D, respectively. The method of joints can be used to determine the forces FCB, FDC,...
1.1K
Design Example: Joints in Concrete Pavements01:28

Design Example: Joints in Concrete Pavements

Concrete pavement joints are essential for maintaining the structural integrity and longevity of pavement by controlling where and how the pavement cracks. These joints can be categorized based on their functions, such as contraction or control joints, construction joints, isolation joints, and expansion joints.
Contraction joints are typically formed by sawing a groove into the concrete shortly after it has hardened. This creates a weakened vertical plane, deliberately encouraging cracking at...
172
Method of Joints01:30

Method of Joints

The method of joints is a commonly used technique to analyze the forces in structural trusses. The method is based on the principle of equilibrium, which assumes that the truss members are connected by frictionless pins. The forces at each joint can be determined by considering the equilibrium of the forces acting on that joint.
Since plane truss members are in the same plane, each joint is subjected to a coplanar and concurrent force system. To apply the method of joints, the first step is to...
728
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
155