相关实验视频

Updated: May 21, 2025

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators
11:44

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

Published on: August 15, 2014

10.3K

对于开关TS模糊系统的事件触发几乎输出调节

Shuanghe Yu, Ying Zhao, Jingjie Xu

    IEEE transactions on cybernetics
    |March 20, 2025
    PubMed
    概括

    本研究介绍了开关TS模糊系统的事件触发 (ET) 方法,确保几乎输出调节 (ETAOR),同时节约资源. 该方法保证了系统的稳定性,并避免了Zeno行为,通过航空发动机示例验证.

    更多相关视频

    A Simple Stimulatory Device for Evoking Point-like Tactile Stimuli: A Searchlight for LFP to Spike Transitions07:34

    A Simple Stimulatory Device for Evoking Point-like Tactile Stimuli: A Searchlight for LFP to Spike Transitions

    Published on: March 25, 2014

    9.8K
    Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator06:45

    Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator

    Published on: October 28, 2022

    1.5K

    相关概念视频

    Biasing of FET01:22

    Biasing of FET

    Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
    In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
    203
    Transient and Steady-state Response01:24

    Transient and Steady-state Response

    In control systems, test signals are essential for evaluating performance under various conditions. The ramp function is effective for systems undergoing gradual changes, while the step function is suitable for assessing systems facing sudden disturbances. For systems subjected to shock inputs, the impulse function is the most appropriate test signal.
    These test signals are integral in designing control systems to exhibit two key performance aspects: transient response and steady-state...
    132
    Second Order systems II01:18

    Second Order systems II

    In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
    75
    Switching of BJT01:22

    Switching of BJT

    Switching behavior in Bipolar Junction Transistors (BJTs) is a fundamental aspect utilized in various electronic circuits, particularly for digital logic applications like switches and amplifiers. In a typical switching circuit, a BJT alternates between cut-off and saturation modes, corresponding to the "off" and "on" states, respectively, thus behaving like an ideal switch.
    Cut-off Mode ("Off" State): In this state, both the emitter-base and collector-base junctions are...
    352
    Reclosers and Fuses01:26

    Reclosers and Fuses

    Automatic circuit reclosers enhance the protection of distribution circuits by interrupting and auto-reclosing an AC circuit according to a preset sequence. They effectively manage temporary faults on overhead distribution lines, often caused by tree limbs or wildlife, by briefly disrupting service to improve overall reliability. However, contact with reclosers or energized broken conductors on the ground can pose serious hazards.
    A comprehensive protection scheme for radial distribution...
    78
    State Space to Transfer Function01:21

    State Space to Transfer Function

    The conversion of state-space representation to a transfer function is a fundamental process in system analysis. It provides a method for transitioning from a time-domain description to a frequency-domain representation, which is crucial for simplifying the analysis and design of control systems.
    The transformation process begins with the state-space representation, characterized by the state equation and the output equation. These equations are typically represented as:
    162