相关实验视频

Updated: May 21, 2025

Assembly and Characterization of an External Driver for the Generation of Sub-Kilohertz Oscillatory Flow in Microchannels
08:32

Assembly and Characterization of an External Driver for the Generation of Sub-Kilohertz Oscillatory Flow in Microchannels

Published on: January 28, 2022

2.3K

分析和设计的新型五声峰级EF类功率放大器

Ehsan Sepahvand1, Akram Sheikhi2

  • 1Electrical Engineering Department, Faculty of Engineering, Lorestan University, Khorramabad, 68151-44316, Iran.

Scientific reports
|March 23, 2025
PubMed
概括

这项研究介绍了高效率的EF类功率放大器 (PA) 的新设计,可以最大限度地降低电感. 新型负载网络实现了宽带宽和高效率,这对于先进的射频应用至关重要.

更多相关视频

Multiplexing Focused Ultrasound Stimulation with Fluorescence Microscopy08:39

Multiplexing Focused Ultrasound Stimulation with Fluorescence Microscopy

Published on: January 7, 2019

8.1K
Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

6.1K

相关概念视频

Design Example: Vintage Mixing Console01:17

Design Example: Vintage Mixing Console

A sound engineer at a music company recently encountered a problem. The output from their newly acquired studio's vintage mixing console was too low for the requirements of modern recording equipment. To rectify this situation, the engineer decided to design an audio pre-amplifier using an operational amplifier (op-amp) to boost the signal level.
The specifications for the pre-amplifier were clear. It needed to amplify the audio signal by a factor of 10, have an input impedance above 10...
189
Small-Signal Analysis of BJT Amplifiers01:21

Small-Signal Analysis of BJT Amplifiers

Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
900
Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
483
Cascaded Op Amps01:16

Cascaded Op Amps

Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
555
BJT Amplifiers01:14

BJT Amplifiers

Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role...
315
Characteristics of Practical Op Amps01:16

Characteristics of Practical Op Amps

A difference amplifier, a crucial component in numerous electronic devices, ideally amplifies only the difference-mode signal, which is the difference between two input signals. However, in practical circuits, the output voltage depends on both the differential gain and the common-mode gain.
The ratio of differential gain to the common-mode gain is defined as the common-mode rejection ratio (CMRR). This ratio quantifies the ability of operational amplifiers (op-amps) to reject common-mode...
429