分析细砂中的透失效机制及其预防和控制研究
1Engineering Department, Huanghe University of Science and Technology, Zhengzhou, 451000, China. 202302002@hhstu.edu.cn.
Scientific reports
|May 6, 2025
概括
地下水透到泥细砂中会造成基础损坏. 建议采用接技术和材料来改善土壤特性,防止透侵蚀,提高工程项目的质量.
科学领域:
- 地质技术工程 地质技术工程
- 水文地质学 水文地质学
背景情况:
- 地下水入泥细砂层可能导致透侵蚀.
- 这种侵蚀导致不均的定居点和基础和地下基础设施的结构损坏.
- 了解流动的土壤和管道机制对于解决这些问题至关重要.
研究的目的:
- 分析地下水透造成的流动土壤和管道的机制.
- 提出有效的接技术,以改善泥细砂层的物理和机械性能.
- 为了防止透破坏基础和地下结构.
主要方法:
- 分析流动的土壤和管道机制.
- 透,分裂和压缩接机制的解释和分析.
- 对各种接材料的审查和讨论.
主要成果:
- 鉴定流动土壤由于有效的粒子重力和管道作为细颗粒迁移.
- 详细介绍了不同接方法的机制.
- 编制了一份潜在的接材料清单,包括植物改性水泥,酸,地聚合物,微生物溶液,纳米盐,乳化青和聚氨.
结论:
- 接是一种可行的技术措施,可以增强泥细砂层.
- 该研究为选择合适的接材料和方法提供了基础.
- 这些发现旨在提高工程项目的质量和耐用性,在粘土细砂环境中.
相关概念视频
01:25Deleterious Substances in Aggregate
128
Deleterious substances in aggregates can be detrimental to the quality and durability of concrete. These substances include organic impurities like loam, which interfere with cement hydration and are usually present in the sand. These prevent a good bond between aggregate and cement paste. Organic impurities can be detected using the colorimetric test, where the darkness of a solution after agitation indicates the level of organic content.
Another type of impurity is clay and fine material that...
Another type of impurity is clay and fine material that...
128
01:24Design Example: Aggregate Gradation
81
The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
81
01:16Segregation in Fresh Concrete
76
Segregation in fresh concrete is a phenomenon where the components of the concrete mix separate, leading to uneven distribution and compromised structural integrity. This separation typically occurs when concrete is subjected to excessive horizontal movement within forms, or when it is dropped from considerable heights or forced through narrow, winding paths. As a result, heavier coarse aggregate particles settle at the bottom, while lighter, finer materials such as cement and water rise to the...
76
01:14Design Example: Managing Concrete Workability
63
This example deals with managing the workability of concrete for a raft foundation project under hot weather conditions. Workability is crucial for ensuring the concrete is easy to place, compact, and finish. In this scenario, a slump test — a common method to measure the workability of fresh concrete — initially indicated low workability. This was attributed to the rapid water loss from the concrete mix, exacerbated by the high temperatures causing the course aggregates to heat up.
63
01:22Effect of Sea Water on Concrete
116
Concrete exposed to seawater can undergo degradation like the dissolution of ettringite and gypsum, increasing the material's porosity and decreasing its strength. In contrast, the crystallization of salts within the concrete's pores can cause expansion, particularly above the waterline where evaporation occurs. Nonetheless, this expansion only happens when seawater, enabled by the concrete's permeability, manages to infiltrate the structure.
Concrete in areas between tide marks,...
Concrete in areas between tide marks,...
116
01:19Sieve Analysis and Grading Curves
234
Sieve analysis is a method used to determine the particle size distribution of aggregate materials. This process involves the following steps:
234