对MWCNT增强复合板的曲行为进行数值研究

相关实验视频

Updated: Sep 13, 2025

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates
07:53

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates

Published on: April 27, 2019

8.4K

Jitendra Singh1, Ajay Kumar2, Barbara Sadowska-Buraczewska3

  • 1Government Engineering College Buxar, Bihar 802103, India.

Materials (Basel, Switzerland)
|July 30, 2025
PubMed
概括

这项研究提出了一种新方法,用于预测用多壁碳纳米管 (MWCNT) 填充剂增强的复合板的曲. 使用先进的理论准确地模型压力,并减少稳定性分析的计算时间.

关键词:
盘子的曲折分析.复合板材是一种复合板材.有限元素方法的有限元素方法.剪切变形板理论 剪切变形板理论

更多相关视频

Author Spotlight: Enhancing Fiber Composite Laminate Quality with the Wet Hand Lay-Up/Vacuum Bag Process09:54

Author Spotlight: Enhancing Fiber Composite Laminate Quality with the Wet Hand Lay-Up/Vacuum Bag Process

Published on: June 30, 2023

2.4K
Strain Sensing Based on Multiscale Composite Materials Reinforced with Graphene Nanoplatelets09:38

Strain Sensing Based on Multiscale Composite Materials Reinforced with Graphene Nanoplatelets

Published on: November 7, 2016

8.9K

相关概念视频

Bending of Members Made of Several Materials01:08

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each...
263
Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
126
Shear and Bending Moment Diagram: Problem Solving01:24

Shear and Bending Moment Diagram: Problem Solving

When analyzing a beam supporting concentrated loads and a distributed load, drawing the shear and bending moment diagrams is essential. These diagrams help understand the internal forces and moments acting on the beam, which is crucial for designing safe and efficient structures. Follow these steps to create the shear and bending moment diagrams:
Draw a Free-Body Diagram: Start by drawing a free-body diagram of the entire beam, including the concentrated loads, distributed load, and reaction...
1.9K
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress...
298
Yield Criteria for Ductile Materials under Plane Stress01:25

Yield Criteria for Ductile Materials under Plane Stress

In designing structural elements and machine parts using ductile materials, it is crucial to ensure that these components withstand applied stresses without yielding. Yielding is initially determined through a tensile test, which evaluates the material's response to uniaxial stress. However, tensile stress is insufficient when components face biaxial or plane stress conditions This condition requires advanced criteria to predict failure.
The Maximum Shearing Stress Criterion, also known as...
216
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
158