相关实验视频

Updated: Jul 18, 2026

Non-Invasive Electrical Brain Stimulation Montages for Modulation of Human Motor Function
07:47

Non-Invasive Electrical Brain Stimulation Montages for Modulation of Human Motor Function

Published on: February 4, 2016

13.6K

跨头电机引起的潜在链接四极组装的安全性

Cinira Diogo1,2,3, Anthony Clanton1,2, Stephen Holmberg1,2

  • 1Nuvasive Clinical Services, Columbia, Maryland.

Journal of clinical neurophysiology : official publication of the American Electroencephalographic Society
|October 17, 2025
PubMed
概括

与双极组合相比,连接的四极组合用于跨电机唤起的潜能 (qTceMEP) 对于脊柱手术是安全的,没有增加严重手术内损伤的风险. 这两种方法都显示,轻微的口腔损伤的发生率很低.

更多相关视频

Concurrent Electroencephalography Recording During Transcranial Alternating Current Stimulation tACS06:51

Concurrent Electroencephalography Recording During Transcranial Alternating Current Stimulation tACS

Published on: January 22, 2016

15.2K
Assessing Primary Motor Cortex Excitability and Excitability Modulation by Pairing Transcranial Magnetic Stimulation with Electromyography12:13

Assessing Primary Motor Cortex Excitability and Excitability Modulation by Pairing Transcranial Magnetic Stimulation with Electromyography

Published on: October 7, 2025

607

相关概念视频

Back EMF01:24

Back EMF

Generators convert mechanical energy into electrical energy, whereas motors convert electrical energy into mechanical energy. A motor works by sending a current through a loop of wire located in a magnetic field. As a result, the magnetic field exerts a torque on the loop. This rotates a shaft, extracting mechanical work from the electrical current sent in initially. When the coil of a motor is turned, magnetic flux changes through the coil, and an emf (consistent with Faraday's law) is induced.
Series R—L Circuit Transients01:22

Series R—L Circuit Transients

In a series resistor-inductor (R-L) circuit, closing the switch at the start of the time period simulates a three-phase short circuit, a fault condition where all three phases of an unloaded synchronous machine are short-circuited. When there is no fault impedance and no initial current, the initial voltage is determined by the phase angle of the source voltage.
Using Kirchhoff's Voltage Law (KVL) to analyze this circuit helps determine the total asymmetrical fault current, which consists of...
Three-Phase Short Circuit—Unloaded Synchronous Machine01:21

Three-Phase Short Circuit—Unloaded Synchronous Machine

Conducting a three-phase short circuit test on an unloaded synchronous machine helps understand its impact on the system. The AC fault current's oscillogram, with the DC offset removed, reveals that the waveform amplitude decreases from an initially high value to a steady-state level for one phase of the machine.
This behavior occurs due to the magnetic flux produced by the short-circuit armature currents. Initially, these currents follow high-reluctance paths but eventually shift to...
Power System Three-Phase Short Circuits01:21

Power System Three-Phase Short Circuits

Determining the subtransient fault current in a power system involves representing transformers by their leakage reactances, transmission lines by their equivalent series reactances, and synchronous machines as constant voltage sources behind their subtransient reactances. In this analysis, certain elements are excluded, such as winding resistances, series resistances, shunt admittances, delta-Y phase shifts, armature resistance, saturation, saliency, non-rotating impedance loads, and small...
Sequence Networks of Rotating Machines01:24

Sequence Networks of Rotating Machines

A Y-connected synchronous generator, grounded through a neutral impedance, is designed to produce balanced internal phase voltages with only positive-sequence components. The generator's sequence networks include a source voltage that is exclusively in the positive-sequence network. The sequence components of line-to-ground voltages at the generator terminals illustrate this configuration.
Zero-sequence current induces a voltage drop across the generator's neutral impedance and other...
Multimachine Stability01:25

Multimachine Stability

Multimachine stability analysis is crucial for understanding the dynamics and stability of power systems with multiple synchronous machines. The objective is to solve the swing equations for a network of M machines connected to an N-bus power system.
In analyzing the system, the nodal equations represent the relationship between bus voltages, machine voltages, and machine currents. The nodal equation is given by: