相关实验视频

Updated: May 6, 2026

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities
11:08

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

Published on: November 30, 2012

19.4K

一个低损耗化网格合器的紧整合设计,基于连续性中的apodized准束状态

Hao Ding, Xinyuan Cao, Mandi Rong

    Optics express
    |November 11, 2025
    PubMed
    概括

    我们开发了一种新的化网格合器,可以在连续 (quasi-BIC) 网格中集成apodized和准-bound状态. 这种设计实现了量子光子电路中光学互连的高合效率和定向性.

    更多相关视频

    Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source12:19

    Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source

    Published on: April 4, 2017

    8.8K
    Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station05:57

    Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station

    Published on: April 1, 2020

    8.5K

    相关概念视频

    Reducing Line Loss01:18

    Reducing Line Loss

    In a three-phase circuit, line loss is an indicator of energy dissipated as heat due to the resistance of transmission lines. To address this, incorporating transformers into the system—a step-up transformer at the source and a step-down transformer at the load—is a strategic solution. Two three-phase transformers are introduced to improve this.
    With a step-up transformer at the source, the voltage is increased, thereby reducing the current in the transmission lines since power loss...
    530
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.9K
    Design of Prismatic Beams for Bending01:23

    Design of Prismatic Beams for Bending

    The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and...
    680
    A Single-Component System01:24

    A Single-Component System

    In the field of chemistry, the terms "component" and "phase" hold significant importance. A component refers to a chemically distinct substance in a system that has specific properties. It is chemically homogeneous, meaning it has the same properties throughout. For example, in a mixture of salt and water, both salt and water are considered separate components because they have different chemical properties.On the other hand, a phase is a form of matter that has a consistent chemical...
    89
    PD Controller: Design01:26

    PD Controller: Design

    In automotive engineering, car suspension systems often employ Proportional Derivative (PD) controllers to enhance performance. PD controllers are utilized to adjust the damping force in response to road conditions. A controller, acting as an amplifier with a constant gain, demonstrates proportional control, with output directly mirroring input.
    Designing a continuous-data controller requires selecting and linking components like adders and integrators, which are fundamental in Proportional,...
    763
    Boundary Conditions: Lossless Lines01:21

    Boundary Conditions: Lossless Lines

    Consider a single-phase, two-wire, lossless transmission line terminated by an impedance at the receiving end and a source with Thevenin voltage and impedance at the sending end. The line, with length, has a surge impedance and wave velocity determined by the line's inductance and capacitance.
    At the receiving end, the boundary condition states that the voltage equals the product of the receiving-end impedance and current. This relationship is expressed as a function of the incident and...
    486