使用基于旋转的水力动力学化装置增强核化:适用于对白醇 - 甲醇 - 水系统的抗溶剂结晶
Vidit Tiwari1, Subhrajit Swain1, Vivek V Ranade1
1Multiphase Reactors and Intensification Group Synthesis and Solid-State Pharmaceutical Research Centre Bernal Institute, University of Limerick, Ireland.
Ultrasonics sonochemistry
|November 19, 2025
概括
液动力学化 (HC) 通过减少诱导时间,显著加快了对醇结晶核化. 这种基于的设备增强了连续结晶过程,提高了产量并防止了设备堵塞.
科学领域:
- 化学工程是化学工程的重要组成部分.
- 结晶科学 结晶科学
背景情况:
- 增强核化速率是加强结晶过程的关键.
- 液动力学化 (HC) 为影响核化动力学提供了一种新的方法.
研究的目的:
- 在甲醇-水系统中研究HC对胺醇结晶核化的作用.
- 开发和实施基于HC的连续核子器,用于过程强化.
主要方法:
- 使用基于的HC装置 (VD) 测量诱导时间的批量实验.
- 开发用于诱导时间估计的相关性.
- 基于VD的连续核子器的设计和测试,与连续振荡混结晶器 (COBC) 集成.
主要成果:
- 诱导时间随着超和的增加而减少.
- HC显著减少了诱导时间,增强了核化.
- 基于VD的核子器提高了COBC产量和生产率,同时减轻了和堵塞.
结论:
- HC有效地增强了对醇的核化,减少了诱导时间.
- 基于VD的连续核子器可用于加强抗溶剂结晶.
- 这项研究为利用HC在工业结晶强化中提供了基础.
相关概念视频
Recrystallization: Solid–Solution Equilibria
2.0K
Recrystallization is a purification technique used to separate impurities from solid compounds. In this technique, no chemical reactions occur. Instead, it exploits physical properties only, specifically, the solubility differences between the desired compound and impurities, either at a single temperature or at different temperatures, and under other selected conditions. The solid-solution equilibrium (solubility equilibrium) of each component in the solution represents a binary phase...
2.0K
Crystal Growth: Principles of Crystallization
4.7K
Crystallization is a phase transformation process in which crystals are precipitated from a supersaturated solution or formed from other sources. During crystallization, atoms or molecules arrange themselves into a well-defined, rigid crystal lattice to minimize energy.
Initiating crystallization involves manipulating the concentration of the solute and the temperature of the solution. Since crystal growth occurs when the ratio of concentration and solubility of the solute in the solvent...
Initiating crystallization involves manipulating the concentration of the solute and the temperature of the solution. Since crystal growth occurs when the ratio of concentration and solubility of the solute in the solvent...
4.7K
Precipitation Processes
4.7K
The experimental conditions in a gravimetric analysis should be optimized to maximize the particle size and purity of the obtained precipitate. Ideally, the concentration of the precipitating reagent should be low with effective stirring to maintain low relative supersaturation for the growth of large crystals. In homogeneous precipitation, the precipitant is slowly generated by a chemical reaction in the solution to avoid local reagent excesses. For example, urea decomposes gradually to...
4.7K
Colloidal precipitates
4.8K
The high insolubility of some precipitates can result in an unfavorable relative supersaturation. This can lead to colloidal particles with a large surface-to-mass ratio, where adsorption is promoted. For instance, in the precipitation of silver chloride, silver ions are adsorbed on the surface of the colloidal particles, forming a primary layer. This layer attracts ions of opposite charge (such as nitrate ions), forming a diffuse secondary layer of adsorbed ions. This electric double layer...
4.8K
Washing, Drying, and Ignition of Precipitates
5.1K
After filtration, the precipitate is washed to remove coprecipitated impurities and any remaining mother liquor. Colloidal precipitates, such as silver chloride, are washed with an electrolyte (such as dilute nitric acid) to prevent the peptization of the precipitate. In the case of slightly soluble precipitates, the wash solution contains a common ion to reduce solubility. Lead sulfate, which is slightly soluble in water, is washed with dilute sulfuric acid. Similarly, wash solutions may be...
5.1K
Precipitate Formation and Particle Size Control
5.1K
In precipitation gravimetry, the precipitating agent should react specifically or selectively with the analyte. While a specific reagent reacts with the analyte alone, a selective reagent can react with a limited number of chemical species.
The obtained precipitate should be either a pure substance of known composition or easily converted to one by a simple process, such as ignition or drying. In addition, the precipitate should be insoluble and easily filterable. In general, filterability...
The obtained precipitate should be either a pure substance of known composition or easily converted to one by a simple process, such as ignition or drying. In addition, the precipitate should be insoluble and easily filterable. In general, filterability...
5.1K


