Related Experiment Video

Updated: Aug 9, 2026

Assessing Cerebral Autoregulation via Oscillatory Lower Body Negative Pressure and Projection Pursuit Regression
11:26

Assessing Cerebral Autoregulation via Oscillatory Lower Body Negative Pressure and Projection Pursuit Regression

Published on: December 10, 2014

Correlations in the adiabatic response of chaotic systems

Auslaender1, Fishman

  • 1Department of Physics, Technion, Haifa 32000, Israel.

Physical Review Letters
|October 4, 2000
PubMed

More Related Videos

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions11:51

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions

Published on: February 22, 2018

Related Concept Videos

Adiabatic Processes for an Ideal Gas01:18

Adiabatic Processes for an Ideal Gas

When an ideal gas is compressed adiabatically, that is, without adding heat, work is done on it, and its temperature increases. In an adiabatic expansion, the gas does work, and its temperature drops. Adiabatic compressions actually occur in the cylinders of a car, where the compressions of the gas-air mixture take place so quickly that there is no time for the mixture to exchange heat with its environment. Nevertheless, because work is done on the mixture during the compression, its...
Pressure and Volume in an Adiabatic Process01:27

Pressure and Volume in an Adiabatic Process

Free expansion of a gas is an adiabatic process. However, there are few differences between free expansion and adiabatic expansion. During free expansion, no work is done, and there is no change in internal energy. But, for an adiabatic expansion, work is done, and there is a change in internal energy. During an adiabatic process, the relation between the pressure and volume is obtained from the condition for the adiabatic process, that is,
Entropy Change in Reversible Processes01:10

Entropy Change in Reversible Processes

In the Carnot engine, which achieves the maximum efficiency between two reservoirs of fixed temperatures, the total change in entropy is zero. The observation can be generalized by considering any reversible cyclic process consisting of many Carnot cycles. Thus, it can be stated that the total entropy change of any ideal reversible cycle is zero.
The statement can be further generalized to prove that entropy is a state function. Take a cyclic process between any two points on a p-V diagram.
Entropy and the Second Law of Thermodynamics01:20

Entropy and the Second Law of Thermodynamics

The second law of thermodynamics can be stated quantitatively using the concept of entropy. Entropy is the measure of disorder of the system.
The relation  between entropy and disorder can be illustrated with the example of the phase change of ice to water. In ice, the molecules are located at specific sites giving a solid state, whereas, in a liquid form, these molecules are much freer to move. The molecular arrangement has therefore become more randomized. Although the change in average...
Entropy and the Second Law of Thermodynamics01:26

Entropy and the Second Law of Thermodynamics

Consider an isolated system in which a hot object is placed in contact with a cold one. This is an irreversible process that eventually leads both objects to reach the same equilibrium temperature. It is crucial to note that the constituents of any substance exhibit increased disorder at higher temperatures. As a cold substance absorbs heat, its constituents become more disordered. The energy transfer from a hotter object to a cooler one increases the system's disorder or randomness. This...
Transient and Steady-state Response01:24

Transient and Steady-state Response

In control systems, test signals are essential for evaluating performance under various conditions. The ramp function is effective for systems undergoing gradual changes, while the step function is suitable for assessing systems facing sudden disturbances. For systems subjected to shock inputs, the impulse function is the most appropriate test signal.
These test signals are integral in designing control systems to exhibit two key performance aspects: transient response and steady-state response.