Related Experiment Video

Updated: Aug 30, 2026

Magnetically Induced Rotating Rayleigh-Taylor Instability
06:42

Magnetically Induced Rotating Rayleigh-Taylor Instability

Published on: March 3, 2017

Statistical analysis of multimode weakly nonlinear Rayleigh-Taylor instability in the presence of surface tension

J Garnier1, C Cherfils-Clérouin, P-A Holstein

  • 1Laboratoire de Statistique et Probabilités, Université Paul Sabatier, 118 Route de Narbonne, 31062 Toulouse Cedex 4, France. garnier@cict.fr

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|October 4, 2003
PubMed

More Related Videos

Microtensiometer for Confocal Microscopy Visualization of Dynamic Interfaces08:05

Microtensiometer for Confocal Microscopy Visualization of Dynamic Interfaces

Published on: September 9, 2022

Related Concept Videos

Surface Tension of Fluid01:22

Surface Tension of Fluid

Surface tension is a fundamental property of fluids, occurring at the boundary between a liquid and a gas or between two immiscible liquids. This phenomenon arises from the cohesive forces between molecules at the fluid's surface, creating an effect similar to a stretched elastic membrane. Inside each fluid, molecules are equally attracted in all directions by neighboring molecules, but surface molecules experience a net inward force, resulting in surface tension.
Surface tension varies with...
Surface Tension01:24

Surface Tension

Surface tension is defined as the force per unit length (γ) acting along the surface of a liquid. It arises due to strong intermolecular forces of attraction. A molecule located inside the bulk of the liquid is surrounded by other molecules and experiences equal forces in all directions. However, a molecule at the surface experiences unbalanced forces because there are more neighboring molecules below than above. This creates a net inward force that pulls surface molecules toward the interior,...
Surface Tension and Surface Energy01:16

Surface Tension and Surface Energy

When a paint brush is immersed in water, the bristles wave freely inside the water. When it is taken out, the bristles stick together. The reason behind this effect is surface tension.
Consider a beaker filled with liquid. The bulk molecules in the liquid experience equal attractive forces on all sides with the surrounding molecules. However, the surface molecules experience a net attractive force downward due to the bulk molecules. The surface of the liquid behaves like a stretched membrane,...
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.