Related Experiment Video

Updated: Aug 26, 2026

Fabrication and Testing of Microfluidic Optomechanical Oscillators
09:10

Fabrication and Testing of Microfluidic Optomechanical Oscillators

Published on: May 29, 2014

One-port noise model of a crystal oscillator

Yuriy S Shmaliy1

  • 1Guanajuato University, Salamanca, Gto., Mexico. shmaliy@salamanca.ugto.mx

IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
|March 5, 2004
PubMed

More Related Videos

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators09:23

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators

Published on: May 30, 2014

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities11:08

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

Published on: November 30, 2012

Related Concept Videos

Oscillations In An LC Circuit01:31

Oscillations In An LC Circuit

An idealized LC circuit of zero resistance can oscillate without any source of emf by shifting the energy stored in the circuit between the electric and magnetic fields. In such an LC circuit, if the capacitor contains a charge q before the switch is closed, then all the energy of the circuit is initially stored in the electric field of the capacitor. This energy is given by
RLC Circuit as a Damped Oscillator01:30

RLC Circuit as a Damped Oscillator

An RLC circuit combines a resistor, inductor, and capacitor, connected in a series or parallel combination.
Consider a series RLC circuit. Here, the presence of resistance in the circuit leads to energy loss due to joule heating in the resistance. Therefore, the total electromagnetic energy in the circuit is no longer constant and decreases with time. Since the magnitude of charge, current, and potential difference continuously decreases, their oscillations are said to be damped. This is...
Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...
Small-signal Diode Model01:18

Small-signal Diode Model

In analyzing the behavior of diodes in circuits, the relationship between the current through a diode and the voltage across it is of particular interest, especially when considering the effect of a direct current (DC) bias voltage. When applied, this DC bias influences the diode's operating point, known as the Q point, around which the current-voltage (I-V) characteristic of the diode exhibits exponential behavior. Introducing a small, time-varying signal on top of this bias aids in examining...
Norton Equivalent Circuits01:16

Norton Equivalent Circuits

Norton's theorem is a fundamental concept in the field of electrical engineering that allows for the simplification of complex AC circuits. The theorem states that any two-terminal linear network can be replaced with an equivalent circuit that consists of an impedance, which is parallel with a constant current source. Figure 1 shows the AC circuit portioned into two parts: Circuit A and Circuit B, while Figure 2 depicts the circuit obtained by replacing Circuit A by its Norton equivalent...
Damped Oscillations01:07

Damped Oscillations

In the real world, oscillations seldom follow true simple harmonic motion. A system that continues its motion indefinitely without losing its amplitude is termed undamped. However, friction of some sort usually dampens the motion, so it fades away or needs more force to continue. For example, a guitar string stops oscillating a few seconds after being plucked. Similarly, one must continually push a swing to keep a child swinging on a playground.
Although friction and other non-conservative...