Related Experiment Video

Updated: Aug 24, 2026

Laser-induced Forward Transfer for Flip-chip Packaging of Single Dies
08:21

Laser-induced Forward Transfer for Flip-chip Packaging of Single Dies

Published on: March 20, 2015

0.18-microm complementary metal-oxide semiconductor push-pull vertical-cavity surface-emitting laser driver operating

David V Plant1, Alan E L Chuah, Michael B Venditti

  • 1Department of Electrical and Computer Engineering, McGill University, Montreal, Quebec, Canada H3A 2A7. plant@photonics.ece.mcgill.ca

Applied Optics
|May 8, 2004
PubMed

More Related Videos

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier10:17

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

Published on: July 12, 2017

Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy08:48

Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy

Published on: November 22, 2019

Related Concept Videos

MOSFET: Enhancement Mode01:22

MOSFET: Enhancement Mode

Enhancement-mode MOSFETs are pivotal components in electronics, distinguished by their capacity to act as highly efficient switches. They are part of the larger family of metal-oxide Semiconductor Field-Effect Transistors (MOSFETs). They are available in two types: p-channel and n-channel, each tailored to specific polarity operations.
In their basic form, enhancement-mode MOSFETs are typically non-conductive when the gate-source voltage (Vgs) is zero. This default 'off' state means no current...
MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
MOSFET01:16

MOSFET

The Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET) plays a pivotal role in modern electronics thanks to its versatility and efficiency in controlling electrical currents. This device, also known as IGFET, MISFET, and MOSFET, has three main terminals: the Source, Drain, and Gate. MOSFETs are classified into n-channel or p-channel types based on the doping characteristics of their substrate and the source or drain regions.
In an n-MOSFET, the structure includes n-type source and drain...
MOSFET: Depletion Mode01:20

MOSFET: Depletion Mode

Depletion-mode MOSFETs represent a unique subset of MOSFET technology, functioning fundamentally differently from their enhancement-mode counterparts. Unlike enhancement MOSFETs, which require a positive gate-source voltage (Vgs) to turn on, depletion-mode MOSFETs are inherently conductive and "normally on" devices.
The primary characteristic of depletion-mode MOSFETs is their ability to conduct current between the drain and source terminals without gate bias. This inherent conductivity arises...
Biasing of FET01:22

Biasing of FET

Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the gate...
Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...