Related Experiment Video

Updated: Aug 18, 2026

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids
11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

Set of measures to analyze the dynamics of nonequilibrium structures

Girish Nathan1, Gemunu Gunaratne

  • 1Department of Physics, University of Houston, 4800 Calhoun Blvd., Houston, TX 77204, USA. Girish.Nathan@mail.uh.edu

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|May 21, 2005
PubMed

More Related Videos

Study of Protein Dynamics via Neutron Spin Echo Spectroscopy08:03

Study of Protein Dynamics via Neutron Spin Echo Spectroscopy

Published on: April 13, 2022

Quantifying Cytoskeleton Dynamics Using Differential Dynamic Microscopy06:37

Quantifying Cytoskeleton Dynamics Using Differential Dynamic Microscopy

Published on: June 15, 2022

Related Concept Videos

Indeterminate Structure01:18

Indeterminate Structure

Indeterminate structures refer to structures where internal forces and reactions cannot be determined using only the equations of static equilibrium.  Indeterminate structures have more unknown forces and reaction forces than equations of static equilibrium that can be used to determine them. Indeterminate structures are often used in engineering to create complex, efficient, and aesthetically pleasing structures. There are various types of indeterminate structures used in engineering and some...
Alternative Sets of Equilibrium Equations01:31

Alternative Sets of Equilibrium Equations

When analyzing the behavior of structures, engineers often rely on the concept of equilibrium. This refers to the state where all forces and moments acting on a system balance each other, resulting in no net movement or rotation. In many cases, equilibrium can be described by a set of standard equations. However, in some situations, alternative sets of equilibrium equations must be used to describe the system's behavior accurately.
One example of such a situation can be observed in a...
Stability of Equilibrium Configuration01:23

Stability of Equilibrium Configuration

Understanding the stability of equilibrium configurations is a fundamental part of mechanical engineering. In any system, there are three distinct types of equilibrium: stable, neutral, and unstable.
A stable equilibrium occurs when a system tends to return to its original position when given a small displacement, and the potential energy is at its minimum. An example of a stable equilibrium is when a cantilever beam is fixed at one end and a weight is attached to the other end. If the weight...
Constraints and Statical Determinacy01:26

Constraints and Statical Determinacy

In structural engineering, the equilibrium of a system is not only determined by its equations of equilibrium but also with the help of constraints. Constraints refer to restrictions on the motion of a system. The proper combinations of constraints can minimize the total number of constraints needed to maintain a system in mechanical equilibrium. When this happens, the system is said to be statically determinate. For such systems, the unknown reaction supports can be estimated using equilibrium...
Energy Diagrams - II01:10

Energy Diagrams - II

Energy diagrams are important to understand the dynamics of a system. The topology of an energy diagram helps illustrate the equilibrium points of the system.
The point in the energy diagram at which the system’s potential energy is the lowest is known as the local minima. The system tends to stay in this position indefinitely unless acted upon by a net force. The slope of the potential energy diagram at the local minima is zero, indicating that zero net force is acting on the system. The slope...
Stability of structures01:14

Stability of structures

In mechanical engineering, the stability of systems under various forces is critical for designing durable and efficient structures. One fundamental way to explore these concepts is by analyzing systems like two rods connected at a pivot point, O, with a torsional spring of spring constant k at the pivot point. This system is similar in appearance to a scissor jack used to change tires on a car. In this case, the arms of the linkage (equivalent to the rods in this system) are entirely vertical,...