Related Experiment Video

Updated: Feb 11, 2026

Motor Dual-Tasks for Gait Analysis and Evaluation in Post-Stroke Patients
05:23

Motor Dual-Tasks for Gait Analysis and Evaluation in Post-Stroke Patients

Published on: March 11, 2021

2.9K

Hemiplegic gait after stroke: is measurement of maximum speed required?

Boudewijn Kollen1, Gert Kwakkel, Eline Lindeman

  • 1Research Bureau, Isala Klinieken, Zwolle, The Netherlands. b.j.kollen@isala.nl

Archives of Physical Medicine and Rehabilitation
|February 28, 2006
PubMed
Abstract

More Related Videos

Lower-Limb Biomechanical Characteristics Associated with Unplanned Gait Termination Under Different Walking Speeds05:52

Lower-Limb Biomechanical Characteristics Associated with Unplanned Gait Termination Under Different Walking Speeds

Published on: August 25, 2020

5.1K
Clinical-oriented Three-dimensional Gait Analysis Method for Evaluating Gait Disorder06:54

Clinical-oriented Three-dimensional Gait Analysis Method for Evaluating Gait Disorder

Published on: March 4, 2018

14.8K

Related Concept Videos

Maximum Deflection01:13

Maximum Deflection

When analyzing beams under unsymmetrical loads, such as a train moving on a bridge, it is crucial to accurately determine the points of maximum stress and deflection. The process involves identifying the maximum deflection of the beam, which may not always occur at its midpoint due to the uneven distribution of the load.
The maximum deflection occurs at a specific point, known as point O, where the tangent to the deflection curve is horizontal. To find point O, the slope of the tangent at any...
1.1K
Maximum Power Transfer01:16

Maximum Power Transfer

Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
By substituting the entire circuit with...
950
Maximum Size of Aggregate01:12

Maximum Size of Aggregate

The maximum size of aggregate is defined as the aperture of the sieve retaining 15 percent or more of the particles present in the aggregate sample. The aggregate's maximum size impacts the concrete's water requirement, workability, and strength. Larger aggregates reduce the surface area needing cement paste coverage, which can lower water needs, thereby allowing a decrease in the water-to-cement ratio when the desired workability and richness of the mix are to be maintained, which can...
569
Requirements for Human Life01:26

Requirements for Human Life

The Earth and its atmosphere have provided humans with air, water, and food, but these are not the only requirements for survival. Humans also require a specific range of temperature and pressure that the Earth and its atmosphere provides.
Oxygen
Atmospheric air is only about 20 percent oxygen, but that oxygen is a key component of the chemical reactions that keep the body alive, including the reactions that produce ATP. Brain cells are susceptible to a lack of oxygen because they require a...
14.1K
The Maximum Power Transfer Theorem01:20

The Maximum Power Transfer Theorem

Consider a linear AC Thevenin equivalent circuit connected to a load impedance.
The load connected draws the current, and the circuit delivers the power to the load. The alternating current flowing through the load is determined using the rectangular form of voltages, currents, network impedance, and load impedance. The average power delivered to the load is obtained from the product of the square of current and load resistance.
1.2K
Maximum Power Flow and Line Loadability01:23

Maximum Power Flow and Line Loadability

The maximum power flow for lossy transmission lines is derived using ABCD parameters in phasor form. These parameters create a matrix relationship between the sending-end and receiving-end voltages and currents, allowing the determination of the receiving-end current. This relationship facilitates calculating the complex power delivered to the receiving end, from which real and reactive power components are derived.
623