Related Experiment Video

Updated: Feb 10, 2026

A Bright NIR-II Fluorescence Probe for Vascular and Tumor Imaging
05:51

A Bright NIR-II Fluorescence Probe for Vascular and Tumor Imaging

Published on: March 17, 2023

2.3K

New fluorescent probes applicable to aggregates of fluorocarbon surfactants

Tadahiro Ozawa1, Tsuyoshi Asakawa, Akio Ohta

  • 1Division of Material Sciences, Graduate School of Natural Science & Technology, Kanazawa University, Kanazawa, Japan.

Journal of Oleo Science
|October 17, 2007
PubMed

More Related Videos

Detection of Protein Aggregation using Fluorescence Correlation Spectroscopy14:04

Detection of Protein Aggregation using Fluorescence Correlation Spectroscopy

Published on: April 25, 2021

6.2K
Preparation of Hollow Polystyrene Particles and Microcapsules by Radical Polymerization of Janus Droplets Consisting of Hydrocarbon and Fluorocarbon Oils07:01

Preparation of Hollow Polystyrene Particles and Microcapsules by Radical Polymerization of Janus Droplets Consisting of Hydrocarbon and Fluorocarbon Oils

Published on: January 25, 2018

10.5K

Related Concept Videos

Aggregates Classification01:29

Aggregates Classification

Aggregate classification is generally based on its size, petrographic characteristics, weight, and source. Size classification ranges from coarse to fine aggregates, defined by the size of the particles. Coarse aggregates are particles that do not pass through ASTM sieve No. 4, and aggregates that pass through the sieve are fine aggregates.
Petrographic classification groups aggregates based on common mineralogical characteristics. Some of the common mineral groups found in aggregates are...
1.0K
Bonding and Strength of Aggregate01:12

Bonding and Strength of Aggregate

The bond between aggregate particles and the cement matrix is significantly influenced by the shape and surface texture of the aggregates. High-strength concretes benefit from a rougher texture, which leads to stronger bonding due to greater adhesion. Angular aggregates with larger surface areas also enhance this bond. The bonding quality, however, is complex to assess as no universally accepted test exists. Good bonding is indicated when a crushed concrete specimen shows some aggregate...
508
Specific Gravity of Aggregate01:19

Specific Gravity of Aggregate

Aggregates typically contain pores, which can be either permeable or impermeable. Considering the pores in the aggregates, the specific gravity of aggregates is defined in three different forms, namely, bulk or gross specific gravity, apparent specific gravity, and absolute specific gravity.
Bulk or gross specific gravity is calculated by taking the ratio of the mass of aggregates in the saturated surface-dry state to the total volume that includes both the solids and the voids within the...
839
Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
1.2K
Preplaced Aggregate Concrete01:29

Preplaced Aggregate Concrete

Preplaced aggregate concrete is ideal for construction environments that are not easily accessible. The process begins by properly wetting the gap-graded coarse aggregates to remove the dirt, then placing it in the form and compacting it. Voids are filled with a mortar mix pumped under pressure through slotted pipes. This mortar typically consists of Portland cement, pozzolan, fine aggregates, water, and a fluidizing aid. The pozzolan helps reduce bleeding and segregation while improving the...
391
Design Example: Aggregate Gradation01:24

Design Example: Aggregate Gradation

The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
342