Related Experiment Video

Updated: Jul 9, 2026

Generation and Coherent Control of Pulsed Quantum Frequency Combs
06:42

Generation and Coherent Control of Pulsed Quantum Frequency Combs

Published on: June 8, 2018

Effects of precompensation and postcompensation on timing jitter in dispersion-managed systems

J Santhanam, C J McKinstrie, T I Lakoba

    Optics Letters
    |December 1, 2007
    PubMed

    More Related Videos

    Gain-compensation Methodology for a Sinusoidal Scan of a Galvanometer Mirror in Proportional-Integral-Differential Control Using Pre-emphasis Techniques09:01

    Gain-compensation Methodology for a Sinusoidal Scan of a Galvanometer Mirror in Proportional-Integral-Differential Control Using Pre-emphasis Techniques

    Published on: April 4, 2017

    Related Concept Videos

    Time and frequency -Domain Interpretation of Phase-lag Control01:21

    Time and frequency -Domain Interpretation of Phase-lag Control

    Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
    Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any finite,...
    ¹H NMR: Interpreting Distorted and Overlapping Signals01:02

    ¹H NMR: Interpreting Distorted and Overlapping Signals

    Spin systems where the difference in chemical shifts of the coupled nuclei is greater than ten times J are called first-order spin systems. These nuclei are weakly coupled, and their chemical shifts and coupling constant can generally be estimated from the well-separated signals in the spectrum.
    As Δν decreases and the signals move closer, the doublets appear increasingly distorted. The intensities of the inner lines increase at the cost of those of the outer lines as the signals are slanted or...
    Time-Domain Interpretation of PD Control01:07

    Time-Domain Interpretation of PD Control

    Proportional-Derivative (PD) control is a widely used control method in various engineering systems to enhance stability and performance. In a system with only proportional control, common issues include high maximum overshoot and oscillation, observed in both the error signal and its rate of change. This behavior can be divided into three distinct phases: initial overshoot, subsequent undershoot, and gradual stabilization.
    Consider the example of control of motor torque. Initially, a positive...
    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    Precipitate Formation and Particle Size Control01:16

    Precipitate Formation and Particle Size Control

    In precipitation gravimetry, the precipitating agent should react specifically or selectively with the analyte. While a specific reagent reacts with the analyte alone, a selective reagent can react with a limited number of chemical species.
    The obtained precipitate should be either a pure substance of known composition or easily converted to one by a simple process, such as ignition or drying. In addition, the precipitate should be insoluble and easily filterable. In general, filterability...
    Propagation of Uncertainty from Systematic Error01:10

    Propagation of Uncertainty from Systematic Error

    The atomic mass of an element varies due to the relative ratio of its isotopes. A sample's relative proportion of oxygen isotopes influences its average atomic mass. For instance, if we were to measure the atomic mass of oxygen from a sample, the mass would be a weighted average of the isotopic masses of oxygen in that sample. Since a single sample is not likely to perfectly reflect the true atomic mass of oxygen for all the molecules of oxygen on Earth, the mass we obtain from this particular...