Related Experiment Video

Updated: Jul 6, 2026

Analyzing Mixing Inhomogeneity in a Microfluidic Device by Microscale Schlieren Technique
10:12

Analyzing Mixing Inhomogeneity in a Microfluidic Device by Microscale Schlieren Technique

Published on: June 12, 2015

Tuning density profiles and mobility of inhomogeneous fluids

Gaurav Goel1, William P Krekelberg, Jeffrey R Errington

  • 1Department of Chemical Engineering, The University of Texas at Austin, Austin, Texas 78712, USA.

Physical Review Letters
|March 21, 2008
PubMed

More Related Videos

Confocal Imaging of Confined Quiescent and Flowing Colloid-polymer Mixtures10:56

Confocal Imaging of Confined Quiescent and Flowing Colloid-polymer Mixtures

Published on: May 20, 2014

The Diffusion of Passive Tracers in Laminar Shear Flow08:01

The Diffusion of Passive Tracers in Laminar Shear Flow

Published on: May 1, 2018

Related Concept Videos

Density00:56

Density

Density is an important characteristic of substances, crucial in determining whether an object sinks or floats in a fluid. Its SI unit is kg/m3, and its cgs unit is g/cm3. The density of an object helps in identifying its composition, and also reveals information about the phase of the matter and its substructure. The densities of liquids and solids are roughly comparable, consistent with the fact that their atoms are in close contact. However, gases have much lower densities than liquids and...
Viscosity of Fluid01:19

Viscosity of Fluid

Viscosity measures the resistance a fluid offers to flow and deformation. It results from internal friction between layers of fluid moving relative to one another. Dynamic viscosity, denoted by the Greek letter mu (μ), quantifies the force needed to move one fluid layer over another. For Newtonian fluids like water and air, the relationship between the shearing stress and the rate of shearing strain is linear, meaning their viscosity remains constant regardless of the applied stress.
Pressure Variation in a Fluid at Rest01:11

Pressure Variation in a Fluid at Rest

In a fluid at rest, the pressure at any point beneath the fluid surface depends solely on the depth, not on the container's shape or size. This principle, known as hydrostatic pressure, arises because, in stationary fluids, there is no acceleration, meaning the forces within the fluid balance out. Only vertical forces, caused by the weight of the fluid above, contribute to pressure changes with depth.
When measuring pressure at two different levels within the fluid, the difference in pressure...
Accelerating Fluids01:17

Accelerating Fluids

When a fluid is in constant acceleration, the pressure and buoyant force equations are modified. Suppose a beaker is placed in an elevator accelerating upward with a constant acceleration, a. In the beaker, assume there is a thin cylinder of height h with an infinitesimal cross-sectional area, ΔS.
The motion of the liquid within this infinitesimal cylinder is considered to obtain the pressure difference. Three vertical forces act on this liquid:
Density, Specific Weight, Specific Gravity and Compressibility of Fluid01:27

Density, Specific Weight, Specific Gravity and Compressibility of Fluid

Density, specific weight, specific gravity, and compressibility are fundamental properties of fluids. Density is the mass per unit volume, characterizing the mass of a fluid system. It influences buoyancy, pressure, flow dynamics, viscosity, thermal conductivity, and sound propagation. For instance, in pipeline design, accurate density measurements ensure that the pipeline can handle the fluid's mass.
Specific weight represents the weight per unit volume and is calculated by multiplying density...
Characteristics of Fluids01:20

Characteristics of Fluids

When a force is applied parallel to the top surface of a solid, it resists the applied force due to the internal frictional forces between the layers of the solid known as shearing resistance. However, when the force is removed, the shearing forces restore the original shape of the solid. Other deformation forces also cause temporary changes in shape if the forces are not beyond a threshold magnitude. Solids tend to retain their shape, making the study of their rest and motion easier. Beyond...