Related Experiment Video

Updated: Jun 4, 2026

Non-invasive Assessments of Subjective and Objective Recovery Characteristics Following an Exhaustive Jump Protocol
08:21

Non-invasive Assessments of Subjective and Objective Recovery Characteristics Following an Exhaustive Jump Protocol

Published on: June 8, 2017

Power-time, force-time, and velocity-time curve analysis during the jump squat: impact of load

Prue Cormie1, Jeffrey M McBride, Grant O McCaulley

  • 1School of Exercise, Biomedical and Health Sciences, Edith Cowan University, Perth, Western Australia.

Journal of Applied Biomechanics
|June 27, 2008
PubMed

More Related Videos

Effects of a Novel Neuromuscular Training Intervention on Jump, Sprint, and Change of Direction in Adult Female Soccer Players10:08

Effects of a Novel Neuromuscular Training Intervention on Jump, Sprint, and Change of Direction in Adult Female Soccer Players

Published on: June 10, 2025

Construction of Constant-Load (Isotonic) and Constant-Velocity (Isokinetic) Torque-Velocity-Power Profiles In vivo for the Rat Plantar Flexors07:44

Construction of Constant-Load (Isotonic) and Constant-Velocity (Isokinetic) Torque-Velocity-Power Profiles In vivo for the Rat Plantar Flexors

Published on: October 3, 2025

Related Concept Videos

Velocity and Position by Graphical Method01:34

Velocity and Position by Graphical Method

Velocity and position can be calculated from the known function of acceleration as a function of time. The total area under the acceleration-time graph and the velocity-time graph gives the change in velocity and position, respectively. In the case of an airplane, its acceleration is tracked using the inertial navigation system. The pilot provides the input of the airplane's initial position and velocity before takeoff. The inertial navigation system then uses the acceleration data to calculate...
Power Expended by a Constant Force00:57

Power Expended by a Constant Force

The relationship between work done and the time taken to do it can be explained using the concept of power. For example, several sprinters in a race may have the same velocity when they reach the finish line, therefore doing the same amount of work, but the winner does it in the least amount of time. Thus, power is defined as the rate of doing work. Since work can vary as a function of time, the average power is defined as the work done during a time interval, divided by the time interval.
Impulse01:13

Impulse

According to Newton’s second law of motion, the rate of change of the momentum of an object is the net external force acting on it. The total change in momentum between two timepoints thus depends on both the external force acting on it and the time over which it acts. Describing this mathematically, the total change of an object’s motion is proportional to the force vector and the time over which it is applied. This product is called impulse.
Additionally, it can be shown that the total...
Impulse-Momentum Theorem00:49

Impulse-Momentum Theorem

The total change in the motion of an object is proportional to the total force vector acting on it and the time over which it acts. This product is called impulse, a vector quantity with the same direction as the total force acting on the object.
By writing Newton's second law of motion in terms of the momentum of an object and the external force acting on it, and simultaneously using the definition of the impulse vector, it can be shown that the total impulse on an object is equal to its net...
Impact Loading01:19

Impact Loading

Impact loading occurs when a moving object collides with a stationary structure, such as a rod with a uniform cross-sectional area fixed at one end. Under these conditions, the rod absorbs the kinetic energy from the striking object, leading to deformation and subsequent stress development. As the rod returns to its original position and reaches maximum stress, the absorbed energy, initially manifested as kinetic energy, transforms entirely into strain energy.
In cases of elastic deformation,...
Impact Loading on a Cantilever Beam01:13

Impact Loading on a Cantilever Beam

The analysis of a cantilever beam with a circular cross-section subjected to impact loading at its free end illustrates the conversion of potential energy from a dropped object into kinetic energy, which is then absorbed by the beam as strain energy. This process is crucial for understanding how materials behave under dynamic loads, which is important in fields such as construction and aerospace.
When an object is dropped onto the free end of a cantilever, its potential energy due to gravity is...