Related Experiment Video

Updated: Jul 3, 2026

Applications of EEG Neuroimaging Data: Event-related Potentials, Spectral Power, and Multiscale Entropy
11:15

Applications of EEG Neuroimaging Data: Event-related Potentials, Spectral Power, and Multiscale Entropy

Published on: June 27, 2013

A method of estimating the noise level in a chaotic time series

A W Jayawardena1, Pengcheng Xu, W K Li

  • 1International Centre for Water Hazard and Risk Management under the auspices of UNESCO, Public Works Research Institute, Tsukuba, Japan. hrecjaw@hkucc.hku.hk

Chaos (Woodbury, N.Y.)
|July 8, 2008
PubMed

More Related Videos

Continuous Measurement of Biological Noise in Escherichia Coli Using Time-lapse Microscopy08:25

Continuous Measurement of Biological Noise in Escherichia Coli Using Time-lapse Microscopy

Published on: April 27, 2021

A Method for Tracking the Time Evolution of Steady-State Evoked Potentials12:03

A Method for Tracking the Time Evolution of Steady-State Evoked Potentials

Published on: May 25, 2019

Related Concept Videos

Random Error01:04

Random Error

Random or indeterminate errors originate from various uncontrollable variables, such as variations in environmental conditions, instrument imperfections, or the inherent variability of the phenomena being measured. Usually, these errors cannot be predicted, estimated, or characterized because their direction and magnitude often vary in magnitude and direction even during consecutive measurements. As a result, they are difficult to eliminate. However, the aggregate effect of these errors can be...
Wald-Wolfowitz Runs Test II01:17

Wald-Wolfowitz Runs Test II

The Wald-Wolfowitz runs test, commonly referred to as the runs test, is a nonparametric test used to assess the randomness of ordered data. The test evaluates the number of runs, which are consecutive sequences of similar elements within the data. If the number of runs is significantly higher or lower than expected, the data is considered non-random, indicating a detectable pattern or structure.
For binary data, runs are identified using symbols such as + and −, or equivalently, 1s and 0s. In...
Estimating Population Mean with Unknown Standard Deviation01:22

Estimating Population Mean with Unknown Standard Deviation

In practice, we rarely know the population standard deviation. In the past, when the sample size was large, this did not present a problem to statisticians. They used the sample standard deviation s as an estimate for σ and proceeded as before to calculate a confidence interval with close enough results. However, statisticians ran into problems when the sample size was small. A small sample size caused inaccuracies in the confidence interval.
William S. Gosset (1876–1937) of the Guinness...
Basic Discrete Time Signals01:16

Basic Discrete Time Signals

The unit step sequence is defined as 1 for zero and positive values of the integer n. This sequence can be graphically displayed using a set of eight sample points, showing a step function starting from n=0 and remaining constant thereafter.
The unit impulse or sample sequence is mathematically expressed as zero for all n values except at n=0, where it is one. The unit impulse sequence, denoted by δ(n), is the first difference of the unit step sequence, while the unit step sequence u(n) is the...
Empirical Method to Interpret Standard Deviation01:09

Empirical Method to Interpret Standard Deviation

The empirical rule, also known as the three-sigma rule, allows a statistician to interpret the standard deviation in a normally distributed dataset. The rule states that 68% of the data lies within one standard deviation from the mean, 95% lies within two standard deviations from the mean, and 99.7% lies within three standard deviations from the mean. Additionally, this rule is also called the 68-95-99.7 rule.
This rule is used widely in statistics to calculate the proportion of data values...
Estimating Population Mean with Known Standard Deviation01:16

Estimating Population Mean with Known Standard Deviation

To construct a confidence interval for a single unknown population mean μ, where the population standard deviation is known, we need sample mean as an estimate for μ and we need the margin of error. Here, the margin of error (EBM) is called the error bound for a population mean (abbreviated EBM). The sample mean is the point estimate of the unknown population mean μ.
The confidence interval estimate will have the form as follows:
(point estimate - error bound, point estimate + error bound)
The...