Related Experiment Video

Updated: Jul 2, 2026

Application of 3D Printing in the Construction of Burr Hole Ring for Deep Brain Stimulation Implants
09:02

Application of 3D Printing in the Construction of Burr Hole Ring for Deep Brain Stimulation Implants

Published on: September 7, 2019

Digit ratio (2D:4D) and wearing of wedding rings

Martin Voracek1

  • 1Department of Basic Psychological Research, School of Psychology, University of Vienna, Liebiggasse 5, Room 03-46, A-1010 Vienna, Austria. martin.voracek@univie.ac.at

Perceptual and Motor Skills
|August 21, 2008
PubMed

More Related Videos

Directed Cellular Self-Assembly to Fabricate Cell-Derived Tissue Rings for Biomechanical Analysis and Tissue Engineering08:00

Directed Cellular Self-Assembly to Fabricate Cell-Derived Tissue Rings for Biomechanical Analysis and Tissue Engineering

Published on: November 25, 2011

Fabrication of Custom Agarose Wells for Cell Seeding and Tissue Ring Self-assembly Using 3D-Printed Molds08:16

Fabrication of Custom Agarose Wells for Cell Seeding and Tissue Ring Self-assembly Using 3D-Printed Molds

Published on: April 2, 2018

Related Concept Videos

Stereoisomerism of Cyclic Compounds02:33

Stereoisomerism of Cyclic Compounds

In this lesson, we delve into the role of ring conformation and its stability, which determines the spatial arrangement and, consequently, the molecular symmetry and stereoisomerism of cyclic compounds. 1,2-Dimethylcyclohexane is used as a case study to evaluate the possible number of stereoisomers. Here, given the multiple (n = 2) chiral centers, there are 2n = 4 possible configurations that lack a plane of symmetry, as the ring skeleton exists in a non-planar chair conformation. In addition,...
The Ratio of X Chromosome to Autosomes02:45

The Ratio of X Chromosome to Autosomes

In most organisms, sex is determined by the ratio of X and Y chromosomes. However, in some organisms, such as Drosophila and C.elegans, sex is determined by the ratio of the number of X chromosomes to the number of sets of autosomes. The Y chromosome in Drosophila is active but does not determine sex. It contains genes responsible for the production of sperms in adult flies.  
Normal male Drosophila has a ratio of one X chromosome to two sets of autosomes. In contrast, normal female Drosophila...
[4+2] Cycloaddition of Conjugated Dienes: Diels–Alder Reaction01:16

[4+2] Cycloaddition of Conjugated Dienes: Diels–Alder Reaction

The Diels–Alder reaction is an example of a thermal pericyclic reaction between a conjugated diene and an alkene or alkyne, commonly referred to as a dienophile. The reaction involves a concerted movement of six π electrons, four from the diene and two from the dienophile, forming an unsaturated six-membered ring. As a result, these reactions are classified as [4+2] cycloadditions.
Handwashing II: Pre-procedure and Initial Procedure Steps01:19

Handwashing II: Pre-procedure and Initial Procedure Steps

The pre-procedure steps of handwashing include removing jewelry and rolling up sleeves. However, many organizations allow staff to wear wedding rings.
The hand washing procedure itself includes the following steps. First, cover cuts, if any, on hands with a waterproof dressing. Cuts and abrasions can become contaminated with bacteria hindering the ability to clean the area thoroughly. In addition, repeated hand washing can worsen an injury.  The nails must be short and clean, without nail paint...
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
Design Example: Calculating Safe Diameter for Wind-Exposed Disc01:17

Design Example: Calculating Safe Diameter for Wind-Exposed Disc

Assessing safety in wind-exposed installations is crucial to preventing potential failures. This example explores the calculation and design adjustments needed to mount a circular disc on a building facade, where wind forces are a primary concern. A 4-meter diameter disc was initially designed as an aesthetic feature facing winds at a velocity of 25 meters per second, with an air density of 1.25 kilograms per cubic meter. Given these conditions, the drag force on the disc was determined using...