Related Experiment Video

Updated: Jun 29, 2026

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres
13:07

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres

Published on: December 1, 2014

Application of constrained optimization to the design of quasi-rugate optical coatings

Alexander V Tikhonravov1, Michael K Trubetskov, Tatiana V Amotchkina

  • 1Research Computing Center, Moscow State University, Leninskie Gory, 119992, Moscow, Russia. tikh@srcc.msu.ru

Applied Optics
|October 3, 2008
PubMed

More Related Videos

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators12:18

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators

Published on: August 5, 2013

The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry12:14

The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry

Published on: August 12, 2013

Related Concept Videos

Lagrange Multipliers: Two Constraints01:28

Lagrange Multipliers: Two Constraints

The method of Lagrange multipliers with two constraints is used to optimize a function subject to two independent constraints. In many applications, the objective function represents a quantity to be maximized or minimized, such as cost, area, distance, or energy. The two constraints represent requirements that the solution must satisfy, such as fixed volume, limited resources, or prescribed dimensions.For a function of three variables, each constraint forms a surface in three-dimensional space.
Optimization Problems01:26

Optimization Problems

Optimization problems often involve identifying maximum or minimum values under specific constraints. A well-known example is determining the longest horizontal pipe that can be moved around a right-angled corner, where a 3-meter-wide hallway meets a 2-meter-wide hallway. This scenario, common in architectural design and industrial transport, can be understood conceptually through geometric and trigonometric reasoning.To visualize the problem, consider the pipe as a straight line that touches...
Design of Prismatic Beams for Bending01:23

Design of Prismatic Beams for Bending

The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and stress...
Lagrange Multipliers: One Constraint01:29

Lagrange Multipliers: One Constraint

In constrained optimization, the objective is to maximize or minimize a quantity while satisfying a fixed condition. A standard example is a rectangular pen built against a barn wall using 100 meters of fencing. Because the wall provides one side of the enclosure, only the other three sides require fencing. The problem is to find the dimensions that produce the greatest possible area.Let L represent the length parallel to the wall and W the width perpendicular to it. The area of the pen is A =...
Application of Nonlinear Inequalities01:29

Application of Nonlinear Inequalities

A nonlinear inequality describes a comparison involving an expression that curves or behaves more complexly than a straight line. These inequalities often appear in forms that include squares, products, or variables in the denominator.To solve such an inequality, one starts by rewriting it so that zero appears on one side. For example, the inequality:  can be factored as: This form makes it easier to identify the values that cause the expression to equal zero. In this case, the key values are 3...
Methods of Medium Optimization01:28

Methods of Medium Optimization

Optimizing growth media enhances microbial proliferation and maximizes product yield. Statistical experimental design methodologies provide structured and reproducible approaches, offering progressively higher levels of robustness and efficiency.The One-Factor-at-a-Time (OFAT) MethodThe One-Factor-at-a-Time (OFAT) method involves adjusting a single variable while keeping all others constant. However, it cannot detect interactions between variables, often leading to suboptimal outcomes when...