Related Experiment Video

Updated: Jun 23, 2026

Development of Amelogenin-chitosan Hydrogel for In Vitro Enamel Regrowth with a Dense Interface
08:26

Development of Amelogenin-chitosan Hydrogel for In Vitro Enamel Regrowth with a Dense Interface

Published on: July 10, 2014

Enamel bond strength of self-etch sealant with and without prior acid etching

Rose O Wadenya1, Marcela Herrera, Jennifer Smith

  • 1wadenya@dental.upenn.edu

The New York State Dental Journal
|May 8, 2009
PubMed

Related Concept Videos

Bonding and Strength of Aggregate01:12

Bonding and Strength of Aggregate

The bond between aggregate particles and the cement matrix is significantly influenced by the shape and surface texture of the aggregates. High-strength concretes benefit from a rougher texture, which leads to stronger bonding due to greater adhesion. Angular aggregates with larger surface areas also enhance this bond. The bonding quality, however, is complex to assess as no universally accepted test exists. Good bonding is indicated when a crushed concrete specimen shows some aggregate...
Acid Strength and Molecular Structure03:05

Acid Strength and Molecular Structure

Binary Acids and Bases
In the absence of any leveling effect, the acid strength of binary compounds of hydrogen with nonmetals (A) increases as the H-A bond strength decreases down a group in the periodic table. For group 17, the order of increasing acidity is HF < HCl < HBr < HI. Likewise, for group 16, the order of increasing acid strength is H2O < H2S < H2Se < H2Te. Across a row in the periodic table, the acid strength of binary hydrogen compounds increases with increasing...
Titration of a Weak Acid with a Strong Base01:30

Titration of a Weak Acid with a Strong Base

In titrating a weak acid with a strong base, different calculation methods are applied at various stages. Initially, the pH of a weak acid like acetic acid is calculated using its dissociation constant (Ka) and an ICE table. Upon addition of a strong base such as sodium hydroxide, a buffer forms, and its pH is determined using the Henderson-Hasselbalch equation. As more base is added and the titration reaches the halfway point, the pH becomes equal to the pKa of the acid, indicating equal...
Masking and Demasking Agents01:19

Masking and Demasking Agents

EDTA titrations may necessitate masking and demasking agents to temporarily protect a particular metal ion in a mixture from the EDTA reaction. These agents facilitate the sequential analysis of the metal ions by forming stable complexes with some—but not all—metal ions during certain steps.
There are many masking agents, such as cyanide, fluoride, triethanolamine, thiourea, and 2,3-bis(sulfanyl)propan-1-ol (formerly 2,3-dimercapto-1-propanol), with the masking agent chosen based on the metal...
Conductometric Titrations: Strong Acid-Weak Base and Weak Acid-Strong Base Titrations01:22

Conductometric Titrations: Strong Acid-Weak Base and Weak Acid-Strong Base Titrations

When a weak acid such as acetic acid is titrated against a strong base like sodium hydroxide, the initial conductance is relatively low due to the weak dissociation of acetic acid. However, as sodium hydroxide is added to the solution, it reacts with the acetic acid to produce highly ionized sodium acetate, which causes an increase in conductance. Once all the acetic acid has been neutralized, any additional sodium hydroxide introduces fast-moving hydroxyl ions, leading to a sharper increase in...
Acid Attack on Concrete01:21

Acid Attack on Concrete

When acids come into contact with concrete, they initiate a chemical reaction that dissolves the hydrated cement paste. This process leads to softening and structural weakening of the concrete. This issue is commonly observed in environments such as chimneys, sewers, and industrial settings. The severity of the damage increases as the pH of the water interacting with the concrete drops below 6.5. In particular, a pH under 4.5 can cause significant concrete damage.
The rate at which hydrogen...