Defect-tolerant demultiplexer circuits based on threshold logic and coding

Related Experiment Video

Updated: Jun 23, 2026

Gene Digital Circuits Based on CRISPR-Cas Systems and Anti-CRISPR Proteins
10:46

Gene Digital Circuits Based on CRISPR-Cas Systems and Anti-CRISPR Proteins

Published on: October 18, 2022

Ron M Roth1, Warren Robinett, Philip J Kuekes

  • 1Computer Science Department, Technion, Haifa 32000, Israel. ronny@cs.technion.ac.il

Nanotechnology
|May 8, 2009
PubMed

More Related Videos

Nanofabrication of Gate-defined GaAs/AlGaAs Lateral Quantum Dots15:47

Nanofabrication of Gate-defined GaAs/AlGaAs Lateral Quantum Dots

Published on: November 1, 2013

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles11:54

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

Published on: March 13, 2017

Related Concept Videos

Clipper Circuit01:18

Clipper Circuit

A clipper circuit is a fundamental wave-shaping device that harnesses the unique properties of diodes to alter and control waveform characteristics. This technology is widely used in electronic devices, especially in television and radar communication systems, where it enhances waveform modulation in both transmitters and receivers.
The operation of a clipper circuit can be exemplified by analyzing a dual-clipper configuration setup that integrates two ideal diodes, each paired with a biasing...
Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
Block Diagram Reduction01:22

Block Diagram Reduction

The process of deriving the transfer function of a control system often involves reducing its block diagram to a single block. This simplification can be achieved through a series of strategic operations, including relocating branch points and comparators. These operations preserve the overall function of the system while allowing for easier manipulation and combination of blocks.
The first step in this process is the identification and relocation of a branch point. A branch point, where a...
Switching of BJT01:22

Switching of BJT

Switching behavior in Bipolar Junction Transistors (BJTs) is a fundamental aspect utilized in various electronic circuits, particularly for digital logic applications like switches and amplifiers. In a typical switching circuit, a BJT alternates between cut-off and saturation modes, corresponding to the "off" and "on" states, respectively, thus behaving like an ideal switch.
Cut-off Mode ("Off" State): In this state, both the emitter-base and collector-base junctions are reverse-biased. The...
MOSFET: Depletion Mode01:20

MOSFET: Depletion Mode

Depletion-mode MOSFETs represent a unique subset of MOSFET technology, functioning fundamentally differently from their enhancement-mode counterparts. Unlike enhancement MOSFETs, which require a positive gate-source voltage (Vgs) to turn on, depletion-mode MOSFETs are inherently conductive and "normally on" devices.
The primary characteristic of depletion-mode MOSFETs is their ability to conduct current between the drain and source terminals without gate bias. This inherent conductivity arises...
Semiconductors01:22

Semiconductors

There is variation in the electrical conductivity of materials - metals, semiconductors, and insulators that are showcased with the help of the energy band diagrams.
Metals such as copper (Cu), zinc (Zn), or lead (Pb) have low resistivity and feature conduction bands that are either not fully occupied or overlap with the valence band, making a bandgap non-existent. This allows electrons in the highest energy levels of the valence band to easily transition to the conduction band upon gaining...