Related Experiment Video

Updated: Jun 22, 2026

Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source
12:19

Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source

Published on: April 4, 2017

Numerical analysis of the performance of Mach-Zehnder interferometric logic gates enhanced with coupled nonlinear

Francisco Cuesta-Soto, Alejandro Martínez, J Blasco

    Optics Express
    |June 18, 2009
    PubMed

    More Related Videos

    Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators09:46

    Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators

    Published on: August 8, 2025

    Implementation of a Reference Interferometer for Nanodetection16:11

    Implementation of a Reference Interferometer for Nanodetection

    Published on: April 26, 2014

    Related Concept Videos

    Design Example: Underdamped Parallel RLC Circuit01:17

    Design Example: Underdamped Parallel RLC Circuit

    Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
    Starting with a fixed...
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    Properties of the z-Transform I01:17

    Properties of the z-Transform I

    The z-transform is a fundamental tool in digital signal processing, enabling the analysis of discrete-time systems through its various properties. It is an invaluable tool for analyzing discrete-time systems, offering a range of properties that simplify complex signal manipulations. One fundamental property is linearity. For any two discrete-time signals, the z-transform of their linear combination equals the same linear combination of their individual z-transforms. This property is essential...
    Second-order Op Amp Circuits01:19

    Second-order Op Amp Circuits

    Implementing second-order low-pass filters in audio systems is crucial in refining audio signals by eliminating undesirable high-frequency noise. These filters typically involve second-order op-amp circuits configured as voltage followers, encompassing two nodes with distinct storage elements.
    The analysis of such circuits follows a systematic approach, similar to the second-order RLC circuits. In practical scenarios, bulky inductors are rarely employed due to their size and weight. This means...