Related Experiment Video

Updated: Jun 21, 2026

Forming, Confining, and Observing Microtubule-Based Active Nematics
08:37

Forming, Confining, and Observing Microtubule-Based Active Nematics

Published on: January 13, 2023

Theory and simulation of two-dimensional nematic and tetratic phases

Jun Geng1, Jonathan V Selinger

  • 1Liquid Crystal Institute, Kent State University, Kent, Ohio 44242, USA.

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|August 8, 2009
PubMed

More Related Videos

High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal06:24

High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal

Published on: October 31, 2019

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets06:26

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets

Published on: May 15, 2017

Related Concept Videos

The Phase Rule01:20

The Phase Rule

The phase rule describes the relationship between the variance (degrees of freedom), the number of components, and the number of phases in a system at equilibrium.Variance is a concept that denotes the number of independent intensive properties (properties are those that do not depend on the amount of material in the system), such as temperature, pressure, and composition, that can be altered without impacting the number of phases in equilibrium.In a single-component system, such as pure water,...
Crystal Field Theory - Tetrahedral and Square Planar Complexes02:46

Crystal Field Theory - Tetrahedral and Square Planar Complexes

Tetrahedral Complexes
Crystal field theory (CFT) is applicable to molecules in geometries other than octahedral. In octahedral complexes, the lobes of the dx2−y2 and dz2 orbitals point directly at the ligands. For tetrahedral complexes, the d orbitals remain in place, but with only four ligands located between the axes. None of the orbitals points directly at the tetrahedral ligands. However, the dx2−y2 and dz2 orbitals (along the Cartesian axes) overlap with the ligands less than the dxy,...
Phase Diagrams of Ternary Systems01:28

Phase Diagrams of Ternary Systems

Consider a ternary system, which is composed of three components: water (W), ethanoic acid (E), and trichloromethane (T). Here, Ethanoic acid (E) is fully miscible with both water (W) and trichloromethane (T), meaning it can mix entirely with either of them. However, water and trichloromethane have partial miscibility, meaning they can only mix to a certain extent, beyond which two separate phases will form.The phase diagram of a ternary system is represented as an equilateral triangle, where...
Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).
Phase Diagram01:24

Phase Diagram

A phase diagram is a graphical representation of the physical states of a substance under different conditions of temperature and pressure. It shows the boundaries between solid, liquid, and gas phases and the conditions at which these phases coexist in equilibrium. An area in a phase diagram represents a single phase, whereas lines or phase boundaries represent the equilibrium between two phases.In the phase diagram of water, the boundary line between the solid and liquid states illustrates...
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...