Related Experiment Video

Updated: Jun 20, 2026

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters
15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

Practical tuning mechanism for fused-tapered couplers

T A Birks

    Optics Letters
    |September 12, 2009
    PubMed

    More Related Videos

    Fabrication and Testing of Microfluidic Optomechanical Oscillators09:10

    Fabrication and Testing of Microfluidic Optomechanical Oscillators

    Published on: May 29, 2014

    Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators11:44

    Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

    Published on: August 15, 2014

    Related Concept Videos

    Problem-Solving: Tuning of a Guitar String01:04

    Problem-Solving: Tuning of a Guitar String

    In the case of stringed instruments like the guitar, the elastic property that determines the speed of the sound produced is its linear mass density or the mass per unit length. This is simply called the linear density. If the string's linear density is constant along the string, then the linear density is simply the total mass divided by the total length.
    The string's wave speed can be regulated by varying the linear density. Tension is the other property that determines the speed of...
    Biasing of FET01:22

    Biasing of FET

    Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
    In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the gate...
    Design of Transmission Shafts01:16

    Design of Transmission Shafts

    The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by reconfiguring the...
    Magnetic Damping01:17

    Magnetic Damping

    Eddy currents can produce significant drag on motion, called magnetic damping. For instance, when a metallic pendulum bob swings between the poles of a strong magnet, significant drag acts on the bob as it enters and leaves the field, quickly damping the motion.
    If, however, the bob is a slotted metal plate, the magnet produces a much smaller effect. When a slotted metal plate enters the field, an emf is induced by the change in flux; however, it is less effective because the slots limit the...
    Bearings: Problem Solving01:24

    Bearings: Problem Solving

    Understanding the calculations and concepts related to double-collar bearings is essential for engineers and designers to optimize the performance of these components in various applications. By analyzing the bearing under different conditions, one can ensure that it can withstand the forces and moments experienced during operation. This knowledge enables better decision-making when designing and selecting bearings for specific purposes and configurations. Consider a double-collar bearing with...
    Potentiometer01:30

    Potentiometer

    Voltage and current measurements using a standard voltmeter and ammeter alter the circuit being measured either by drawing or resisting the current flow, which introduces uncertainties in the measurements. Null measurements balance the voltages so that no current flows through the measuring device and, therefore, no alterations occur in the measured circuit.
    Suppose the emf of a battery needs to be measured. If the battery is directly connected to a standard voltmeter, the measured quantity is...