Related Experiment Video

Updated: Jun 18, 2026

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes
11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

Published on: December 13, 2016

Increasing the production accuracy of profile bending with methods of computational intelligence

Alessandro Selvaggio1, Uwe Dirksen, A Erman Tekkaya

  • 1Institute of Forming Technology and Lightweight Construction, TU Dortmund, Dortmund, 44227, Germany. Alessandro.Selvaggio@iul.tu-dortmund.de

Evolutionary Computation
|November 18, 2009
PubMed

More Related Videos

Automatic Laser-based Geometry Capture for Finite Element Analysis of Weld Beads07:58

Automatic Laser-based Geometry Capture for Finite Element Analysis of Weld Beads

Published on: July 25, 2025

Operation of the Collaborative Composite Manufacturing (CCM) System10:09

Operation of the Collaborative Composite Manufacturing (CCM) System

Published on: October 1, 2019

Related Concept Videos

Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
Bending01:10

Bending

Pure bending is a fundamental concept in structural mechanics, essential for understanding how materials deform under symmetrical loads without direct forces. Pure bending occurs when prismatic members, such as beams, are subjected to equal and opposite moments that induce bending. The phenomenon is crucial as it allows for predicting stress distributions without the influence of axial or shear forces.
In pure bending, the bending stress in a beam is calculated based on the bending moment and...
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member is the...
Simpson's Rule II01:28

Simpson's Rule II

In warehouse roofing applications, corrugated or curved metal sheets are commonly used to improve structural strength, water drainage, and ventilation efficiency. To accurately estimate material requirements and optimize design parameters, engineers must determine the curved surface area of these sheets. Because the sheet profiles often repeat smoothly along their length, they can be effectively approximated by parabolic curves, enabling the use of numerical integration techniques for area...
Unsymmetric Bending01:18

Unsymmetric Bending

Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from those in symmetrical bending, and are essential for designing structures to withstand different loading conditions. In unsymmetrical bending, the neutral axis—where stress is zero—does not necessarily align with the geometric axes of the cross-section. The orientation of the...