Related Experiment Video
Updated: Jun 17, 2026

12:08
Fabrication of High Contrast Gratings for the Spectrum Splitting Dispersive Element in a Concentrated Photovoltaic System
Published on: July 18, 2015
Abstract:
The intensification property of a multilayer structure of aligned plane transmission diffraction gratings (pile-of-gratings) is described. A first-order analysis is given, based on addition of intensities, and the conditions under which intensification is possible are derived. Supporting experimental results are described.
Related Concept Videos
Interference and Diffraction
Interference is a characteristic phenomenon exhibited by waves. When two electromagnetic waves interact with their peaks and troughs coinciding, a resulting wave with enhanced amplitude is produced. This is known as constructive interference. In this case, the two waves interacting are in phase with each other.
Graded Potential
Graded potentials are localized fluctuations in the cell membrane's electrical charge, commonly found in the dendrites of neurons. The magnitude of these potential changes depends on the strength of the initiating stimulus. In a membrane at its resting potential, a graded potential signifies a voltage shift either above -70 mV or below -70 mV.
Graded potentials fall into two categories: depolarizing and hyperpolarizing. Depolarizing graded potentials typically occur when sodium (Na+) or calcium...
Graded potentials fall into two categories: depolarizing and hyperpolarizing. Depolarizing graded potentials typically occur when sodium (Na+) or calcium...
Design Example: Aggregate Gradation
The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is sampled...
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is sampled...
Convolution Properties II
The important convolution properties include width, area, differentiation, and integration properties.
The width property indicates that if the durations of input signals are T1 and T2, then the width of the output response equals the sum of both durations, irrespective of the shapes of the two functions. For instance, convolving two rectangular pulses with durations of 2 seconds and 1 second results in a function with a width of 3 seconds.
The area property asserts that the area under the...
The width property indicates that if the durations of input signals are T1 and T2, then the width of the output response equals the sum of both durations, irrespective of the shapes of the two functions. For instance, convolving two rectangular pulses with durations of 2 seconds and 1 second results in a function with a width of 3 seconds.
The area property asserts that the area under the...
Types of Aggregate Grading
Aggregate grading is crucial in economically obtaining a concrete mix with adequate strength, reasonable workability, and minimal segregation. There are four types of aggregate gradation: well-graded, uniformly (or one-sized) graded, gap-graded, and open-graded.
Well-graded aggregates include a complete range of necessary size fractions that fit together to create a dense matrix with minimal voids, represented by a smooth, continuous gradation curve. This type of grading ensures good...
Well-graded aggregates include a complete range of necessary size fractions that fit together to create a dense matrix with minimal voids, represented by a smooth, continuous gradation curve. This type of grading ensures good...
Sound Intensity
The loudness of a sound source is related to how energetically the source is vibrating, consequently making the molecules of the propagation medium vibrate. To measure the loudness of a source, the physical quantity of interest is the intensity. This is defined as the energy emitted per unit of time per unit of area perpendicular to the sound wave's propagation direction. Since the total energy is greater if the source vibrates for a longer duration and over a larger area, dividing the emitted...

