Related Experiment Video

Updated: Jun 16, 2026

Compact Lens-less Digital Holographic Microscope for MEMS Inspection and Characterization
10:28

Compact Lens-less Digital Holographic Microscope for MEMS Inspection and Characterization

Published on: July 5, 2016

Measurement of deformation in a cylindrical shell by holographic interferometry

T Matsumoto, K Iwata, R Nagata

    Applied Optics
    |February 4, 2010
    PubMed

    More Related Videos

    Uncovering Hidden Dynamics of Natural Photonic Structures Using Holographic Imaging05:45

    Uncovering Hidden Dynamics of Natural Photonic Structures Using Holographic Imaging

    Published on: March 31, 2022

    Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes06:56

    Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

    Published on: May 23, 2017

    Related Concept Videos

    Plastic Deformation in Circular Shafts01:20

    Plastic Deformation in Circular Shafts

    When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
    Deformation in a Circular Shaft01:10

    Deformation in a Circular Shaft

    One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
    Deformation of Member under Multiple Loadings01:11

    Deformation of Member under Multiple Loadings

    When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
    In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
    Measurements of Strain01:27

    Measurements of Strain

    Strain quantifies the deformation of a material under force, typically measured as normal strain, which represents the change in length when compared with the original length. Electrical strain gauges are used for enhanced accuracy. These devices consist of a conductive wire mounted on a paper backing that adheres to the material's surface. These gauges operate on the piezoresistive effect, where the wire's electrical resistance changes in response to mechanical deformation. The strain gauge...
    Temperature Dependent Deformation01:12

    Temperature Dependent Deformation

    In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added together...
    Deformations in a Symmetric Member in Bending01:18

    Deformations in a Symmetric Member in Bending

    When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
    When the member is segmented into tiny cubic elements, it is observed that the primary stress...