Related Experiment Video

Updated: Jun 13, 2026

Standardizing a Non-Lethal Method for Characterizing the Reproductive Status and Larval Development of Freshwater Mussels (Bivalvia: Unionida)
07:22

Standardizing a Non-Lethal Method for Characterizing the Reproductive Status and Larval Development of Freshwater Mussels (Bivalvia: Unionida)

Published on: October 4, 2019

Bivalve population health: multistress to identify hot spots

X de Montaudouin1, I Paul-Pont, C Lambert

  • 1University Bordeaux 1, EPOC CNRS UMR 5805, Station Marine d'Arcachon, 2 rue du Pr Jolyet, 33120 Arcachon, France. x.de-montaudouin@epoc.u-bordeaux1.fr

Marine Pollution Bulletin
|April 17, 2010
PubMed

More Related Videos

A Strain Gauge Monitor (SGM) for Continuous Valve Gape Measurements in Bivalve Molluscs in Response to Laboratory Induced Diel-cycling Hypoxia and pH07:59

A Strain Gauge Monitor (SGM) for Continuous Valve Gape Measurements in Bivalve Molluscs in Response to Laboratory Induced Diel-cycling Hypoxia and pH

Published on: August 1, 2018

Bioindication Testing of Stream Environment Suitability for Young Freshwater Pearl Mussels Using In Situ Exposure Methods07:53

Bioindication Testing of Stream Environment Suitability for Young Freshwater Pearl Mussels Using In Situ Exposure Methods

Published on: September 5, 2018

Related Concept Videos

Methods to Assess Microbial Populations01:30

Methods to Assess Microbial Populations

Assessing microbial populations is crucial for understanding microbial roles in health, ecology, and industry. Various complementary techniques—both culture-based and molecular—enable detailed analysis of microbial abundance, diversity, and function.Viable Plate CountThe viable plate count is a traditional culture-based method used to estimate the number of living microbes in a sample. After serial dilution, the sample is spread onto nutrient agar plates. Each viable cell forms a visible...
Freshwater Microbial Ecology01:24

Freshwater Microbial Ecology

Freshwater systems such as streams, rivers, and lakes exhibit distinct physical and biological characteristics that influence their microbial communities. These environments are broadly categorized into lotic systems—those with flowing waters like streams and most rivers—and lentic systems, which include still or slow-moving waters such as lakes, ponds, and marshes.In lentic systems, phytoplankton drive primary production, generating autochthonous organic carbon. In contrast, lotic systems...
Conservation of Declining Populations02:07

Conservation of Declining Populations

Conservation of declining population focuses on ways of detecting, diagnosing, and halting a population decline. The approach uses methods to prevent populations from going extinct.
Conservation of Small Populations02:04

Conservation of Small Populations

Small population sizes put a species at extreme risk of extinction due to a lack of variation, and a consequent decrease in adaptability. This weakens the chances of survival under pressures such as climate change, competition from other species, or new diseases. Large populations are more likely to survive pressures such as these, as such populations are more likely to harbor individuals that have genetic variants that are adaptive under new stresses. Small populations are much less likely to...
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress concentration...