Related Experiment Video

Updated: Jun 12, 2026

Characterizing Lewis Pairs Using Titration Coupled with In Situ Infrared Spectroscopy
07:49

Characterizing Lewis Pairs Using Titration Coupled with In Situ Infrared Spectroscopy

Published on: February 20, 2020

Low-valent iron-catalyzed C-C bond formation-addition, substitution, and C-H bond activation

Eiichi Nakamura1, Naohiko Yoshikai

  • 1Department of Chemistry, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033, Japan. nakamura@chem.s.u-tokyo.ac.jp

The Journal of Organic Chemistry
|June 5, 2010
PubMed

More Related Videos

Versatile CO2 Transformations into Complex Products: A One-pot Two-step Strategy07:36

Versatile CO2 Transformations into Complex Products: A One-pot Two-step Strategy

Published on: November 9, 2019

Synthesis of Antiviral Tetrahydrocarbazole Derivatives by Photochemical and Acid-catalyzed C-H Functionalization via Intermediate Peroxides (CHIPS)06:34

Synthesis of Antiviral Tetrahydrocarbazole Derivatives by Photochemical and Acid-catalyzed C-H Functionalization via Intermediate Peroxides (CHIPS)

Published on: June 20, 2014

Related Concept Videos

C–C Bond Formation: Aldol Condensation Overview01:10

C–C Bond Formation: Aldol Condensation Overview

Aldol condensation is an important route in synthetic organic chemistry used to generate a new carbon–carbon bond under basic or acidic conditions. The aldol condensation reaction presented in Figure 1 constitutes an aldol addition reaction followed by the dehydration process.
Properties of Organometallic Compounds01:23

Properties of Organometallic Compounds

Organometallic compounds are compounds that contain a carbon–metal bond. Carbon belongs to an organyl group like alkyl, aryl, allyl, or benzyl groups. The metal can be from Group I or Group II of the periodic table, a transition metal, or a semimetal.
Cycloaddition Reactions: MO Requirements for Thermal Activation01:16

Cycloaddition Reactions: MO Requirements for Thermal Activation

Thermal cycloadditions are reactions where the source of activation energy needed to initiate the reaction is provided in the form of heat. A typical example of a thermally-allowed cycloaddition is the Diels–Alder reaction, which is a [4 + 2] cycloaddition. In contrast, a [2 + 2] cycloaddition is thermally forbidden.
Reduction of Alkynes to cis-Alkenes: Catalytic Hydrogenation02:24

Reduction of Alkynes to cis-Alkenes: Catalytic Hydrogenation

Introduction
Like alkenes, alkynes can be reduced to alkanes in the presence of transition metal catalysts such as Pt, Pd, or Ni. The reaction involves two sequential syn additions of hydrogen via a cis-alkene intermediate.
Conjugate Addition (1,4-Addition) vs Direct Addition (1,2-Addition)01:27

Conjugate Addition (1,4-Addition) vs Direct Addition (1,2-Addition)

α,β-Unsaturated carbonyl compounds with two electrophilic sites, the carbonyl carbon, and the β carbon, are susceptible to nucleophilic attack via two modes: conjugate or 1,4-addition and direct or 1,2-addition.
Conjugate addition results in a thermodynamically stable product. The reaction retains the stronger C=O bond at the expense of the weaker C=C π bond. The process is slow as the β carbon is less electrophilic than the carbonyl carbon.
Direct addition products are formed faster owing to...
Reduction of Alkenes: Asymmetric Catalytic Hydrogenation02:17

Reduction of Alkenes: Asymmetric Catalytic Hydrogenation

Catalytic hydrogenation of alkenes is a transition-metal catalyzed reduction of the double bond using molecular hydrogen to give alkanes. The mode of hydrogen addition follows syn stereochemistry.
The metal catalyst used can be either heterogeneous or homogeneous. When hydrogenation of an alkene generates a chiral center, a pair of enantiomeric products is expected to form. However, an enantiomeric excess of one of the products can be facilitated using an enantioselective reaction or an...