Jove
Visualize
Contact Us
JoVE
x logofacebook logolinkedin logoyoutube logo
ABOUT JoVE
OverviewLeadershipBlogJoVE Help Center
AUTHORS
Publishing ProcessEditorial BoardScope & PoliciesPeer ReviewFAQSubmit
LIBRARIANS
TestimonialsSubscriptionsAccessResourcesLibrary Advisory BoardFAQ
RESEARCH
JoVE JournalMethods CollectionsJoVE Encyclopedia of ExperimentsArchive
EDUCATION
JoVE CoreJoVE BusinessJoVE Science EducationJoVE Lab ManualFaculty Resource CenterFaculty Site
Terms & Conditions of Use
Privacy Policy
Policies

Related Concept Videos

Gain01:15

Gain

Gain and phase shift are properties of linear circuits that describe the effect a circuit has on a sinusoidal input voltage or current. The circuit's behavior that contains reactive elements will depend on the frequency of the input sinusoid. As a result, it is observed that the gain and phase shift will all be frequency functions.
Gain:
Suppose Vin is the input and Vout is the output signal to a circuit.
Lossless Lines01:23

Lossless Lines

In electrical engineering, a lossless transmission line is characterized by a purely imaginary propagation constant and a resistive characteristic impedance. The ABCD parameters, which describe the relationship between the input and output voltages and currents, indicate an equivalent π circuit with an imaginary series impedance and a shunt admittance. This results in a transmission line that, when the product of the phase constant (beta) and the length of the line is less than pi, exhibits...
Time and frequency -Domain Interpretation of Phase-lead Control01:24

Time and frequency -Domain Interpretation of Phase-lead Control

Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
Phase Contrast and Differential Interference Contrast Microscopy01:26

Phase Contrast and Differential Interference Contrast Microscopy

Phase-Contrast Microscopes
In-phase-contrast microscopes, interference between light directly passing through a cell and light refracted by cellular components is used to create high-contrast, high-resolution images without staining. It is the oldest and simplest type of microscope that creates an image by altering the wavelengths of light rays passing through the specimen. Altered wavelength paths are created using an annular stop in the condenser. The annular stop produces a hollow cone of...
Time and frequency -Domain Interpretation of Phase-lag Control01:21

Time and frequency -Domain Interpretation of Phase-lag Control

Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any finite,...

You might also read

Related Articles

Articles linked to this work by shared authors, journal, and citation graph.

Sort by
Same author

Effect of phase noise in linear modulator systems.

Applied optics·2010
Same author

Broadband LiTaO(3) guided-wave TE-TM mode converter.

Applied optics·2010
Same author

Coupling model for fused fiber couplers with parabolic taper shape.

Applied optics·2010
Same author

Parabolic model for shape of fiber taper.

Applied optics·2010
Same author

Effect of laser diode spontaneous emission on IOSA operation.

Applied optics·2010
Same author

Propagation characteristics of single-mode evanescent field couplers.

Applied optics·2010

Related Experiment Video

Updated: Jun 12, 2026

Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station
05:57

Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station

Published on: April 1, 2020

Analytic output expression for integrated optic phase reversal modulators with microwave loss.

W K Burns

    Applied Optics
    |June 18, 2010
    PubMed
    Summary

    This study provides analytic expressions for integrated optic phase reversal modulators, accounting for microwave loss. The findings apply to various modulator types with consistent segment lengths, aiding optical modulator design.

    More Related Videos

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator
    08:39

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

    Published on: January 28, 2019

    Related Experiment Videos

    Last Updated: Jun 12, 2026

    Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station
    05:57

    Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station

    Published on: April 1, 2020

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator
    08:39

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

    Published on: January 28, 2019

    Area of Science:

    • Photonics and Optical Engineering
    • Electrical Engineering

    Background:

    • Integrated optic phase reversal modulators are key components in optical communication systems.
    • Understanding their performance, especially with microwave loss, is crucial for signal integrity.

    Purpose of the Study:

    • To derive analytic output expressions for the amplitude and phase of integrated optic phase reversal modulators.
    • To incorporate the effects of microwave loss into these expressions.

    Main Methods:

    • Development of analytical models to describe modulator output.
    • Inclusion of microwave loss parameters in the mathematical formulations.

    Main Results:

    • Formulas for output amplitude and phase derived, considering microwave loss.
    • The results are applicable to both periodic and aperiodic modulators with constant segment length.

    Conclusions:

    • The derived expressions offer a precise method for analyzing modulator performance.
    • This work facilitates the design and optimization of integrated optic modulators in high-frequency applications.