Related Experiment Video

Updated: May 29, 2026

Combining Microfluidics and Microrheology to Determine Rheological Properties of Soft Matter during Repeated Phase Transitions
11:38

Combining Microfluidics and Microrheology to Determine Rheological Properties of Soft Matter during Repeated Phase Transitions

Published on: April 19, 2018

Dynamical behavior near a liquid-liquid phase transition in simulations of supercooled water

Peter H Poole1, Stephen R Becker, Francesco Sciortino

  • 1Department of Physics, St. Francis Xavier University, Antigonish, Nova Scotia B2G 2W5, Canada. ppoole@stfx.ca

The Journal of Physical Chemistry. B
|August 27, 2011
PubMed

More Related Videos

Phase Diagram Characterization Using Magnetic Beads as Liquid Carriers12:37

Phase Diagram Characterization Using Magnetic Beads as Liquid Carriers

Published on: September 4, 2015

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets06:26

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets

Published on: May 15, 2017

Related Concept Videos

Phase Transitions: Vaporization and Condensation02:39

Phase Transitions: Vaporization and Condensation

The physical form of a substance changes on changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize (convert into vapor). The process is called vaporization—a surface phenomenon. Vaporization occurs when the thermal motion of the molecules overcome the intermolecular forces, and the molecules (at the surface) escape into the gaseous state. When a liquid vaporizes in a closed container, gas molecules cannot escape. As these gas phase molecules...
Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
Phase Transitions: Sublimation and Deposition02:33

Phase Transitions: Sublimation and Deposition

Some solids can transition directly into the gaseous state, bypassing the liquid state, via a process known as sublimation. At room temperature and standard pressure, a piece of dry ice (solid CO2) sublimes, appearing to gradually disappear without ever forming any liquid. Snow and ice sublimate at temperatures below the melting point of water, a slow process that may be accelerated by winds and the reduced atmospheric pressures at high altitudes. When solid iodine is warmed, the solid sublimes...
Phase Diagram01:24

Phase Diagram

A phase diagram is a graphical representation of the physical states of a substance under different conditions of temperature and pressure. It shows the boundaries between solid, liquid, and gas phases and the conditions at which these phases coexist in equilibrium. An area in a phase diagram represents a single phase, whereas lines or phase boundaries represent the equilibrium between two phases.In the phase diagram of water, the boundary line between the solid and liquid states illustrates...
Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).