Related Experiment Video

Updated: May 25, 2026

High-pressure, High-temperature Deformation Experiment Using the New Generation Griggs-type Apparatus
12:30

High-pressure, High-temperature Deformation Experiment Using the New Generation Griggs-type Apparatus

Published on: April 3, 2018

Creating a high temperature environment at high pressure in a gas piston cylinder apparatus

P C Burnley1, I C Getting

  • 1High Pressure Science and Engineering Center and Department of Geoscience, University of Nevada, Las Vegas, Las Vegas, Nevada 89154, USA. Burnley@physics.unlv.edu

The Review of Scientific Instruments
|February 4, 2012
PubMed

More Related Videos

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System10:52

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

Published on: August 7, 2018

Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions11:50

Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions

Published on: June 13, 2015

Related Concept Videos

The Joule and Joule–Thomson Experiments01:23

The Joule and Joule–Thomson Experiments

Consider an adiabatic system composed of two chambers, A and B, designed such that no heat flows into or out of the system. Initially, chamber A is filled with a gas at a fixed temperature T1, pressure p1, and volume V1, while chamber B is evacuated. The gas is then gradually forced through a rigid, porous barrier to chamber B, ultimately reaching temperature T2, pressure p2, and volume V2. A piston on the right side maintains a constant pressure (p2), which is lower than p1. The significant...
Heat Capacities of an Ideal Gas I01:14

Heat Capacities of an Ideal Gas I

Heat capacity is the ratio of heat absorbed by the substance corresponding to its temperature change. It is also called thermal capacity and the SI unit of heat capacity is J/K. Whereas, specific heat capacity is defined as the amount of heat necessary to change the temperature of 1 kg of a substance by 1 K and is also called massic heat capacity. Its SI unit is J/kg⋅K.
Molar heat capacity quantifies the ratio of the amount of heat added (or removed) to increase (or decrease) the temperature of...
Adiabatic Processes for an Ideal Gas01:18

Adiabatic Processes for an Ideal Gas

When an ideal gas is compressed adiabatically, that is, without adding heat, work is done on it, and its temperature increases. In an adiabatic expansion, the gas does work, and its temperature drops. Adiabatic compressions actually occur in the cylinders of a car, where the compressions of the gas-air mixture take place so quickly that there is no time for the mixture to exchange heat with its environment. Nevertheless, because work is done on the mixture during the compression, its...
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
Isothermal Processes01:21

Isothermal Processes

A thermodynamic process that occurs at constant temperature is called an isothermal process. Heat slowly flows into the system or out of the system to maintain thermal equilibrium. Processes involving phase changes like water evaporation into steam or freezing water into ice at a constant temperature are examples of Isothermal Processes.
An ideal gas can also undergo isothermal expansion or compression.
For example, consider 1 mole of an ideal gas inside an isolated cylinder at initial volume V...
Path Between Thermodynamics States01:21

Path Between Thermodynamics States

Consider the two thermodynamic processes involving an ideal gas that are represented by paths AC and ABC in Figure 1: