Related Experiment Video

Updated: May 24, 2026

Manufacturing Simple and Inexpensive Soil Surface Temperature and Gravimetric Water Content Sensors
08:49

Manufacturing Simple and Inexpensive Soil Surface Temperature and Gravimetric Water Content Sensors

Published on: December 21, 2019

Monitoring of water content in building materials using a wireless passive sensor

Goran Stojanović1, Milan Radovanović, Mirjana Malešev

  • 1Faculty of Technical Sciences, University of Novi Sad, Trg Dositeja Obradovića 6, 21000 Novi Sad, Serbia. sgoran@uns.ac.rs

Sensors (Basel, Switzerland)
|March 9, 2012
PubMed

Keywords:
LC sensorbuilding materialshumiditywireless

More Related Videos

In Situ Soil Moisture Sensors in Undisturbed Soils08:20

In Situ Soil Moisture Sensors in Undisturbed Soils

Published on: November 18, 2022

BtM, a Low-cost Open-source Datalogger to Estimate the Water Content of Nonvascular Cryptogams08:25

BtM, a Low-cost Open-source Datalogger to Estimate the Water Content of Nonvascular Cryptogams

Published on: March 25, 2019

Related Concept Videos

Measurement of Air Content in Concrete01:23

Measurement of Air Content in Concrete

Air content measurement in concrete is critical for ensuring structural integrity and durability of concrete structures, especially in environments prone to severe weather conditions. Accurate air content analysis optimizes concrete's resistance to freeze-thaw cycles and enhances its workability and strength. Several methods are standardized under ASTM guidelines to measure the air content in fresh concrete, each suitable for different concrete types and conditions.
The pressure method,...
Moisture Content and Bulking of Aggregate01:10

Moisture Content and Bulking of Aggregate

The moisture content of aggregates is a crucial factor in construction, particularly in concrete mixing, as it influences the total water required in the mix. Moisture content represents the water coated on the exterior surface of the aggregate existing in a saturated and surface-dry condition. The total water content of a moist aggregate is the sum of its moisture content and water absorption.
When aggregates are exposed to rain or sit in stockpiles, they absorb moisture, which must be...
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the aggregate...
Microbial Biosensors01:17

Microbial Biosensors

Microbial biosensors are analytical devices that utilize living microbes to detect specific substances through measurable signals. These devices consist of two main components: biosensing organisms and signal-transducing elements. Biosensing organisms, such as Escherichia coli or Saccharomyces cerevisiae, are typically housed in multiwell plates connected to transducers, enabling rapid, real-time detection of target analytes.Signal Generation MechanismWhen a target analyte—such as...
Key Elements for Plant Nutrition02:35

Key Elements for Plant Nutrition

Like all living organisms, plants require organic and inorganic nutrients to survive, reproduce, grow and maintain homeostasis. To identify nutrients that are essential for plant functioning, researchers have leveraged a technique called hydroponics. In hydroponic culture systems, plants are grown—without soil—in water-based solutions containing nutrients. At least 17 nutrients have been identified as essential elements required by plants. Plants acquire these elements from the atmosphere, the...
Testing Water Quality01:14

Testing Water Quality

When the quality of water for concrete preparation is uncertain, its impact on the setting time of cement and compressive strength of mortar is assessed by comparison with de-ionized or distilled water benchmarks. American Society for Testing and Materials (ASTM) C1602 requires the setting times to be within 90 minutes of the control, British Standard (BS) 3146:1980 allows a 30-minute variance in the initial setting, while British Standards European Norm (BS EN) 1008 specifies initial setting...