Related Experiment Video

Updated: May 21, 2026

Back Mechanical Sensitivity Assessment in the Rat for Mechanistic Investigation of Chronic Back Pain
05:10

Back Mechanical Sensitivity Assessment in the Rat for Mechanistic Investigation of Chronic Back Pain

Published on: August 30, 2022

Study on work load and work-related musculoskeletal disorders amongst male jute mill workers of West Bengal, India

Moumita Sett1, Subhashis Sahu

  • 1Department of Physiology, University of Kalyani, Nadia, West Bengal, India.

Work (Reading, Mass.)
|June 16, 2012
PubMed
Abstract

More Related Videos

Induction and Assessment of Exertional Skeletal Muscle Damage in Humans08:33

Induction and Assessment of Exertional Skeletal Muscle Damage in Humans

Published on: December 11, 2016

Exploring the Longissimus Muscle: Unraveling its Correlation with Meat Quality in Bos indicus and Crossbred Bulls07:46

Exploring the Longissimus Muscle: Unraveling its Correlation with Meat Quality in Bos indicus and Crossbred Bulls

Published on: July 12, 2024

Related Concept Videos

Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
Factors Affecting Workability01:24

Factors Affecting Workability

The workability of concrete is a critical characteristic that influences the ease of mixing, handling, and finishing the concrete. It is affected by several factors including water content, aggregate properties, and admixtures like air entrainment. Water plays a fundamental role as it lubricates the concrete mix, facilitating easier movement and placement. However, the water requirement varies depending on the texture and shape of aggregates. Finer particles and angular, rough-textured...
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Applications of Stress01:04

Applications of Stress

Consider a structure made of a boom and a rod designed to support a load. These two components are connected by a pin and stabilized by brackets and pins. The boom and the rod are detached from their supports to assess the different stresses imposed on this structure, and a free-body diagram is drawn. Then, all the forces applied, including the load acting on the structure, are identified. The reaction forces exerted on both the boom and the rod are computed using the equilibrium equations.
The...
Bearing Stress01:22

Bearing Stress

Bearing stress refers to the contact pressure between two separate bodies. To visualize this, imagine a bolt thrust through a plate. The bolt applies a force to the plate, which exerts an equal but opposite force back onto the bolt. This force isn't just a singular entity but a compilation of numerous smaller forces distributed across the contact surface between the bolt and the plate.
Due to the intricacy of these microforces, an average value, known as bearing stress, is often used by...
Normal Strain under Axial Loading01:20

Normal Strain under Axial Loading

Normal strain under axial loading is an important concept in the field of mechanics of materials. Axial loading implies the application of a force along the axis of a material, like a column or bar. This force can either compress or stretch the material. In the context of axial loading, normal strain is the deformation experienced by the material in the direction of the loading force. It's calculated as the change in length divided by the original length of the material. This unitless ratio...