Related Experiment Video

Updated: May 18, 2026

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids
11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

Nonperturbative renormalization group study of the stochastic Navier-Stokes equation

Carlos Mejía-Monasterio1, Paolo Muratore-Ginanneschi

  • 1Laboratory of Physical Properties, Department of Rural Engineering, Technical University of Madrid, Av. Complutense s/n, 28040 Madrid, Spain. carlos.mejia@upm.es

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|September 26, 2012
PubMed

More Related Videos

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions11:51

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions

Published on: February 22, 2018

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section11:00

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section

Published on: July 19, 2016

Related Concept Videos

Navier–Stokes Equations01:28

Navier–Stokes Equations

For incompressible Newtonian fluids, where density remains constant, stresses show a linear relationship with the deformation rate, defined by normal and shear stresses. Normal stresses depend on the pressure exerted on the fluid and the rate of deformation in specific directions, which determines how fluid flows under varying pressures. Shear stresses, on the other hand, act tangentially across fluid layers. They explain how adjacent fluid layers slide relative to one another, connecting...
Dimensionless Groups in Fluid Mechanics01:15

Dimensionless Groups in Fluid Mechanics

Dimensionless groups in fluid mechanics provide simplified ratios that help analyze fluid behavior without relying on specific units. The Reynolds number (Re), which represents the ratio of inertial to viscous forces, distinguishes between laminar and turbulent flows, making it essential in the design of pipelines and aerodynamic surfaces. The Froude number (Fr), the ratio of inertial to gravitational forces, is particularly useful in predicting wave formation and hydraulic jumps in...
Bernoulli's Equation for Flow Normal to a Streamline01:16

Bernoulli's Equation for Flow Normal to a Streamline

Bernoulli's equation for flow normal to a streamline explains how pressure varies across curved streamlines due to the outward centrifugal forces induced by the fluid's curvature. The pressure is higher on the inner side of the curve, near the center of curvature, and decreases outward to balance these centrifugal forces.
The pressure difference depends on the fluid's velocity and radius of curvature. The pressure variation is minimal in flows with nearly straight streamlines. However, the...
Typical Model Studies01:30

Typical Model Studies

Fluid mechanics model studies often utilize scaled-down systems to predict fluid behavior in full-scale environments, such as river flows, dam spillways, and structures interacting with open surfaces. Maintaining Froude number similarity in river models is crucial, as it replicates surface flow features like wave patterns and velocities.
The Buckingham Pi Theorem01:09

The Buckingham Pi Theorem

The Buckingham Pi theorem provides a structured method to simplify fluid dynamics problems by reducing complex systems of variables to dimensionless terms.
Reynolds Transport Theorem01:24

Reynolds Transport Theorem

The Reynolds transport theorem provides a framework to relate the time rate of change of an extensive property within a system to that in a control volume, which is crucial for analyzing fluid dynamics. Extensive properties, such as mass, velocity, acceleration, temperature, and momentum, can be expressed in terms of the mass of a fluid portion. These properties are called extensive because they depend on the system's size, while intensive properties are their corresponding values per unit mass.