Related Experiment Video

Updated: May 17, 2026

The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry
12:14

The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry

Published on: August 12, 2013

Self-referenced technique for the determination of meridional figure errors of a toroidal mirror with a Sagnac

Sanjib Chatterjee1, Y Pavan Kumar

  • 1Raja Ramanna Centre for Advanced Technology, Department of Atomic Energy, Indore, India. schat@rrcat.gov.in

Applied Optics
|October 24, 2012
PubMed

More Related Videos

Magnetic Tweezers for the Measurement of Twist and Torque11:41

Magnetic Tweezers for the Measurement of Twist and Torque

Published on: May 19, 2014

Gain-compensation Methodology for a Sinusoidal Scan of a Galvanometer Mirror in Proportional-Integral-Differential Control Using Pre-emphasis Techniques09:01

Gain-compensation Methodology for a Sinusoidal Scan of a Galvanometer Mirror in Proportional-Integral-Differential Control Using Pre-emphasis Techniques

Published on: April 4, 2017

Related Concept Videos

Adjusting a Traverse01:12

Adjusting a Traverse

In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
Meridians01:28

Meridians

In surveying, meridians are vital reference lines to measure directions and establish accurate land orientations. Meridians run from the north to the south poles, providing a stable framework for angular measurements and mapping. Meridians are fundamental in survey design, with the primary types being astronomic, magnetic, and assumed meridians. Each type offers distinct benefits and limitations, selected based on the project's scale and precision needs.The astronomic meridian is aligned with...
Trigonometric Substitution01:23

Trigonometric Substitution

Trigonometric substitution is a technique used to simplify integrals that contain square root expressions involving quadratic forms. It is particularly effective when the integrand includes terms resembling those found in standard geometric equations, such as circles or ellipses.Molniya satellites follow highly elliptical orbits, repeatedly sweeping out the same regions of space as they revolve around Earth. To estimate the area enclosed by such an orbit, the path is modeled as an ellipse...
Gauss's Law: Spherical Symmetry01:26

Gauss's Law: Spherical Symmetry

A charge distribution has spherical symmetry if the density of charge depends only on the distance from a point in space and not on the direction. In other words, if the system is rotated, it doesn't look different. For instance, if a sphere of radius R is uniformly charged with charge density ρ0, then the distribution has spherical symmetry. On the other hand, if a sphere of radius R is charged so that the top half of the sphere has a uniform charge density ρ1 and the bottom half has a uniform...
NMR Spectrometers: Resolution and Error Correction01:14

NMR Spectrometers: Resolution and Error Correction

When magnetic nuclei in a sample achieve resonance and undergo relaxation, the signal detected in NMR is an approximately exponential free induction decay. Fourier transform of an exponential decay yields a Lorentzian peak in the frequency domain. Lorentzian peaks in an NMR spectrum are defined by their amplitude, full width at half maximum, and position, where the peak width is governed by the spin-spin relaxation time alone. In real experiments, however, the applied magnetic field is rendered...
Common Leveling Mistakes and Errors01:17

Common Leveling Mistakes and Errors

A survey team is tasked with determining the elevation difference between points Point A and Point B, separated by uneven terrain. They use a leveling instrument and a leveling rod.Common MistakesMisreading the Rod: During a backsight reading at Point A, the instrumentman observes the rod partially obscured by tall grass. Instead of reading 1.135 m, they mistakenly record 1.735 m due to the misalignment of the crosshair with the wrong graduation. This error adds 0.600 m to all subsequent...