A study of obliquity of femoral shaft in Eastern Indian population

Related Experiment Video

Updated: May 13, 2026

In Vivo Quantification of Hip Arthrokinematics during Dynamic Weight-bearing Activities using Dual Fluoroscopy
07:43

In Vivo Quantification of Hip Arthrokinematics during Dynamic Weight-bearing Activities using Dual Fluoroscopy

Published on: July 2, 2021

S Mistri1, A Bhakta, G C Mondal

  • 1Department of Anatomy, NRS Medical College, Kolkata - 700014, India. mousutsav10@bsnl.in

Nepal Medical College Journal : NMCJ
|February 28, 2013
PubMed

More Related Videos

Three-Dimensional Preoperative Virtual Planning in Derotational Proximal Femoral Osteotomy08:15

Three-Dimensional Preoperative Virtual Planning in Derotational Proximal Femoral Osteotomy

Published on: February 17, 2023

Scanning Skeletal Remains for Bone Mineral Density in Forensic Contexts07:56

Scanning Skeletal Remains for Bone Mineral Density in Forensic Contexts

Published on: January 29, 2018

Related Concept Videos

Bones of the Lower Limb: Femur and Patella01:16

Bones of the Lower Limb: Femur and Patella

The femur is the body's longest and strongest bone spanning the thigh region. Its head articulates with the acetabulum of the hip bone to form the hip joint. A minor indentation on the medial side of the femoral head, called the fovea capitis, serves as the site of attachment for the ligament of the head of the femur. This weak ligament spans the femur and acetabulum and supports the hip joint. The narrowed region below the head is the neck of the femur. The inclination angle between the neck...
Changes in the Appendicular Skeleton with Age01:09

Changes in the Appendicular Skeleton with Age

The upper and lower limb initially develops as a small bulge called a limb bud, which appears on the lateral side of the early embryo. The upper limb bud appears near the end of the fourth week of development, with the lower limb bud appearing shortly after.
Initially, the limb buds consist of a core of mesenchyme covered by a layer of ectoderm. The ectoderm at the end of the limb bud thickens to form a narrow crest called the apical ectodermal ridge. This ridge stimulates the underlying...
Bones of the Lower Limb: Tibia and Fibula01:10

Bones of the Lower Limb: Tibia and Fibula

The tibia is the main weight-bearing bone of the lower leg. It is larger than the fibula with which it is paired. The tibia is also the second longest bone in the body and is located right below the skin. The proximal end of the tibia forms the medial and the lateral condyle, which articulates with the condyles of the femur to form the knee joint. Between the articulating surfaces is the irregular elevated area known as the intercondylar eminence that serves as the inferior attachment point for...
General Case of Eccentric Axial Loading01:12

General Case of Eccentric Axial Loading

Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from symmetrical bending, which are essential for designing structures to withstand different loading conditions.
Consider a member subjected to equal and opposite forces that are applied along a line that does not coincide with the member's neutral axis. In unsymmetrical bending,...
Bones of the Upper Limb: Humerus01:19

Bones of the Upper Limb: Humerus

The upper limb consists of the arm, forearm, wrist, and hand bones. The humerus is the single bone of the upper arm region. Proximally, it has a large, spherical, smooth head that articulates with the glenoid cavity of the scapula to form the glenohumeral or shoulder joint. The margin of the head is the anatomical neck, a residual epiphyseal plate. Laterally it extends to form bony projections called the greater tubercle and the lesser tubercle. Next to the tubercles is the surgical neck, a...
Eccentric Axial Loading in a Plane of Symmetry01:16

Eccentric Axial Loading in a Plane of Symmetry

Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.