Related Experiment Video

Updated: May 13, 2026

Visualizing Hyporheic Flow Through Bedforms Using Dye Experiments and Simulation
09:49

Visualizing Hyporheic Flow Through Bedforms Using Dye Experiments and Simulation

Published on: November 18, 2015

A leaky aquifer below Champlain Sea clay: closed-form solutions for natural seepage

Robert P Chapuis1, Antoine Saucier

  • 1Department MAGI, École Polytechnique de Montréal, P.O. Box 6079, Sta. CV, Montreal, QC, Canada H3C 3A7.

Ground Water
|February 28, 2013
PubMed

More Related Videos

Design and Use of a Full Flow Sampling System (FFS) for the Quantification of Methane Emissions08:18

Design and Use of a Full Flow Sampling System (FFS) for the Quantification of Methane Emissions

Published on: June 12, 2016

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores09:32

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores

Published on: November 20, 2014

Related Concept Videos

Uniform Depth Channel Flow01:27

Uniform Depth Channel Flow

Uniform depth channel flow keeps fluid depth consistent along channels such as irrigation canals. In natural channels, such as rivers, approximate uniform flow is often assumed. This condition occurs when the channel’s bottom slope matches the energy slope, balancing potential energy lost from gravity with head loss due to shear stress. This balance prevents depth changes along the channel length, resulting in a steady, uniform flow.Uniform flow in open channels with a constant cross-section...
Uniform Depth Channel Flow: Problem Solving01:18

Uniform Depth Channel Flow: Problem Solving

To calculate the flow rate for a trapezoidal channel, first, identify the bottom width, side slope, and flow depth of the channel. The cross-sectional area (A) corresponding to the depth of flow (y), channel bottom width (B), and side slope (θ) is determined by:Next, calculate the wetted perimeter, which includes the bottom width and the sloped side lengths in contact with the water. Using the values of the cross-sectional area and the wetted perimeter, determine the hydraulic radius by...
Design Example: Creating a Hydraulic Model of a Dam Spillway01:21

Design Example: Creating a Hydraulic Model of a Dam Spillway

Scaled hydraulic models of dam spillways provide a practical way to replicate and study the intricate flow dynamics of these structures. Often built to a 1:15 ratio, these models allow for observing critical water behavior, such as velocity distribution, flow patterns, and energy dissipation.
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to viscous...
Indefinite Integrals01:25

Indefinite Integrals

The water inflow rate into a storage tank is not constant but increases over time. Initially, the pump delivers water at a rate of 5 L/min. However, the inflow rate increases by 2 L/min for each additional minute due to rising pressure or system adjustments. This scenario can be described mathematically by a linear function:It is necessary to integrate the inflow rate function to measure the total volume of water added to the tank over time. The total water volume V(t) is obtained by performing...
Fundamental Theorem of Calculus I: Problem Solving01:22

Fundamental Theorem of Calculus I: Problem Solving

In many engineering and environmental applications, accumulated quantities are determined from rates that vary over time. A common example arises in water management, where a supply system pumps water into a storage tank at a rate that changes with time. Accurately determining how much water has entered the tank over a given period is essential for maintaining proper pressure, scheduling operations, and ensuring system safety.The flow rate of water into the tank is described by a time-dependent...