Related Experiment Video

Updated: May 11, 2026

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Published on: April 11, 2018

[Modelling of the knee joint loading conditions in the view of mechanics]

K B Pustovoĭt, M Iu Karpins'kyĭ

Klinichna Khirurhiia

|May 28, 2013

Abstract:

The results of mathematic modelling of work of femoropatellar joint in normal conditions and in the presence of dysplastic deformity were adduced. There was established, that a knee joint (KJ) by its external appearance and function constitutes a classic cam mechanism. Biomechanical scheme of interaction between the femoral bone processus and patella was elaborated. In accordance to scheme of cam mechanism its experimental roentgenometric investigations were performed. According to statistical analysis performed, in conditions of dysplasia in femoropatellar joint the changes in the KJ occur, which may cause its blockade; the patella position in the KJ depends on peculiarities of anatomical structure of the femoral bone processuses.

More Related Videos

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis

Published on: May 8, 2014

Imaging of the Microstructural Failure Mechanism in the Human Hip

Imaging of the Microstructural Failure Mechanism in the Human Hip

Published on: September 29, 2023

Related Concept Videos

Deformation of Member under Multiple Loadings

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.

Stress: General Loading Conditions

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.

Knee Joint

Knee Joint

The knee joint is the most complicated joint in the body. It consists of three articulations– two tibiofemoral and one patellofemoral. As is characteristic of synovial joints, the knee joint has a thin articular capsule that partially surrounds this joint cavity. Additionally, several ligaments, muscles, and cartilaginous structures support the movement of the knee.
A total of seven ligaments support the knee joint. The patellar ligament, which is also attached to the quadriceps femoris group...

Eccentric Axial Loading in a Plane of Symmetry

Eccentric Axial Loading in a Plane of Symmetry

Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.

Method of Joints: Problem Solving II

Method of Joints: Problem Solving II

Consider a truss structure with frictionless joints fixed to a wall and roller support. If a force of 150 N is applied to joint A, the forces in each member of the truss can be determined using the method of joints.