Related Experiment Video

Updated: May 7, 2026

Phase-Dependent Control of Trap Depth and Persistent Luminescence in Strontium Aluminate Phosphors
06:16

Phase-Dependent Control of Trap Depth and Persistent Luminescence in Strontium Aluminate Phosphors

Published on: December 5, 2025

The polar phase of Li2Ge4O9 at 298, 150 and 90 K

Günther J Redhammer1, Gerold Tippelt

  • 1Department of Materials Science and Physics, Division of Mineralogy, University of Salzburg, 5020 Salzburg, Austria.

Acta Crystallographica. Section C, Crystal Structure Communications
|October 8, 2013
PubMed

Keywords:
crystal structurelithium germanates

More Related Videos

1,3,5-Triphenylbenzene and Corannulene as Electron Receptors for Lithium Solvated Electron Solutions06:56

1,3,5-Triphenylbenzene and Corannulene as Electron Receptors for Lithium Solvated Electron Solutions

Published on: October 10, 2016

Phase Diagram Characterization Using Magnetic Beads as Liquid Carriers12:37

Phase Diagram Characterization Using Magnetic Beads as Liquid Carriers

Published on: September 4, 2015

Related Concept Videos

Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).
Phase Diagram01:24

Phase Diagram

A phase diagram is a graphical representation of the physical states of a substance under different conditions of temperature and pressure. It shows the boundaries between solid, liquid, and gas phases and the conditions at which these phases coexist in equilibrium. An area in a phase diagram represents a single phase, whereas lines or phase boundaries represent the equilibrium between two phases.In the phase diagram of water, the boundary line between the solid and liquid states illustrates...
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
Phase Transitions: Sublimation and Deposition02:33

Phase Transitions: Sublimation and Deposition

Some solids can transition directly into the gaseous state, bypassing the liquid state, via a process known as sublimation. At room temperature and standard pressure, a piece of dry ice (solid CO2) sublimes, appearing to gradually disappear without ever forming any liquid. Snow and ice sublimate at temperatures below the melting point of water, a slow process that may be accelerated by winds and the reduced atmospheric pressures at high altitudes. When solid iodine is warmed, the solid sublimes...
Phase Transitions01:21

Phase Transitions

A phase transition is the process in which a substance changes from one state of matter to another, like from a solid to a liquid, liquid to gas, or vice versa, at a specific temperature and under given pressure conditions. This change is spontaneous and is affected by alterations in temperature and pressure. These parameters impact the strength of the forces between molecules (intermolecular forces) in the substance.During a phase transition, both the initial and final phases of the substance...