Related Experiment Video

Updated: May 6, 2026

Collection of Skeletal Muscle Biopsies from the Superior Compartment of Human Musculus Tibialis Anterior for Mechanical Evaluation
05:18

Collection of Skeletal Muscle Biopsies from the Superior Compartment of Human Musculus Tibialis Anterior for Mechanical Evaluation

Published on: September 27, 2020

6.7K

Bending performance of large mode area multi-trench fibers

Deepak Jain, Catherine Baskiotis, Jayanta Kumar Sahu

    Optics Express
    |November 13, 2013
    PubMed

    More Related Videos

    Effect of Bending on the Electrical Characteristics of Flexible Organic Single Crystal-based Field-effect Transistors08:43

    Effect of Bending on the Electrical Characteristics of Flexible Organic Single Crystal-based Field-effect Transistors

    Published on: November 7, 2016

    7.3K
    Measurement of Maximum Isometric Force Generated by Permeabilized Skeletal Muscle Fibers11:30

    Measurement of Maximum Isometric Force Generated by Permeabilized Skeletal Muscle Fibers

    Published on: June 16, 2015

    27.6K

    Related Concept Videos

    Bending of Members Made of Several Materials01:11

    Bending of Members Made of Several Materials

    In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
    Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
    764
    Members Made of Elastoplastic Material01:19

    Members Made of Elastoplastic Material

    The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
    As the bending moment...
    538
    Bending01:10

    Bending

    Pure bending is a fundamental concept in structural mechanics, essential for understanding how materials deform under symmetrical loads without direct forces. Pure bending occurs when prismatic members, such as beams, are subjected to equal and opposite moments that induce bending. The phenomenon is crucial as it allows for predicting stress distributions without the influence of axial or shear forces.
    In pure bending, the bending stress in a beam is calculated based on the bending moment and...
    1.3K
    Deformations in a Transverse Cross Section01:21

    Deformations in a Transverse Cross Section

    When a material is subjected to uniaxial stress, it elongates or contracts in the direction of the applied force, and also undergoes changes in the perpendicular directions. This behavior is crucial for understanding how materials behave under stress and is governed by mechanical properties such as Poisson's ratio v, which measures the ratio of transverse strain to axial strain.
    As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
    718
    Bending of Curved Members - Strain Analysis01:14

    Bending of Curved Members - Strain Analysis

    The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
    The important part of bending analysis for such a member...
    678
    Unsymmetric Bending01:18

    Unsymmetric Bending

    Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from those in symmetrical bending, and are essential for designing structures to withstand different loading conditions. In unsymmetrical bending, the neutral axis—where stress is zero—does not necessarily align with the geometric axes of the cross-section. The...
    992