Related Experiment Video

Updated: May 3, 2026

Subsurface Defect Localization by Structured Heating Using Laser Projected Photothermal Thermography
11:34

Subsurface Defect Localization by Structured Heating Using Laser Projected Photothermal Thermography

Published on: May 15, 2017

10.5K

Athermal compensation of the stress-induced surface deflection of optical coatings using iso-admittance layers

Frédéric Lemarquis

    Applied Optics
    |February 12, 2014
    PubMed

    More Related Videos

    Cooling Rate Dependent Ellipsometry Measurements to Determine the Dynamics of Thin Glassy Films09:32

    Cooling Rate Dependent Ellipsometry Measurements to Determine the Dynamics of Thin Glassy Films

    Published on: January 26, 2016

    7.9K
    Atomic Layer Deposition of Vanadium Dioxide and a Temperature-dependent Optical Model11:10

    Atomic Layer Deposition of Vanadium Dioxide and a Temperature-dependent Optical Model

    Published on: May 23, 2018

    12.7K

    Related Concept Videos

    Thermal Stress01:09

    Thermal Stress

    If the temperature of an object is changed while it is prevented from expanding or contracting, the object is subjected to stress. The stress is compressive if the object expands in the absence of constraint and tensile if it contracts. This stress resulting from temperature change is known as thermal stress. It can be quite large and can cause damage. To avoid this stress, engineers may design components so they can expand and contract freely. For instance, on highways, gaps are deliberately...
    2.5K
    Thermal Strain01:19

    Thermal Strain

    Thermal strain is a concept that arises when we consider how temperature changes affect structures. Unlike the conventional assumption that structures remain constant under load, real-world scenarios often involve temperature fluctuations that can significantly impact these structures. Consider a homogeneous rod with a uniform cross-section resting freely on a flat horizontal surface. If the rod's temperature increases, the rod elongates. This elongation is proportional to the temperature...
    3.2K
    Thermal expansion and Thermal stress: Problem Solving01:27

    Thermal expansion and Thermal stress: Problem Solving

    San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
    To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in temperature (ΔT) is 55...
    2.2K
    Stress Concentrations01:24

    Stress Concentrations

    Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller...
    834
    Temperature Dependent Deformation01:12

    Temperature Dependent Deformation

    In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
    742
    Deformations in a Transverse Cross Section01:21

    Deformations in a Transverse Cross Section

    When a material is subjected to uniaxial stress, it elongates or contracts in the direction of the applied force, and also undergoes changes in the perpendicular directions. This behavior is crucial for understanding how materials behave under stress and is governed by mechanical properties such as Poisson's ratio v, which measures the ratio of transverse strain to axial strain.
    As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
    716