Related Experiment Video

Updated: Apr 30, 2026

A Guide to Concentration Alternating Frequency Response Analysis of Fuel Cells
11:18

A Guide to Concentration Alternating Frequency Response Analysis of Fuel Cells

Published on: December 11, 2019

5.9K

Performance improvement of a microbial fuel cell based on adaptive fuzzy control

Liping Fan1, Chong Li2, Kosta Boshnakov3

  • 1College of Environment and Safety Engineering, Shenyang University of Chemical Technology, Shenyang, China.

Pakistan Journal of Pharmaceutical Sciences
|May 13, 2014
PubMed

More Related Videos

Optimize Flue Gas Settings to Promote Microalgae Growth in Photobioreactors via Computer Simulations14:33

Optimize Flue Gas Settings to Promote Microalgae Growth in Photobioreactors via Computer Simulations

Published on: October 1, 2013

13.9K
Coupling Carbon Capture from a Power Plant with Semi-automated Open Raceway Ponds for Microalgae Cultivation08:17

Coupling Carbon Capture from a Power Plant with Semi-automated Open Raceway Ponds for Microalgae Cultivation

Published on: August 14, 2020

5.1K

Related Concept Videos

Bioreactor Controls-I01:28

Bioreactor Controls-I

Maintaining optimal conditions within fermenters is essential for maximizing microbial productivity and ensuring process efficiency. This lesson focuses on key parameters—temperature, foam, pH, carbon dioxide, oxygen, and pressure—and their precise measurement and control strategies in fermentation systems.Temperature ControlTemperature regulation is critical due to the exothermic nature of many fermentation processes. In small laboratory fermenters, temperature is commonly...
93
Bioreactor Controls-II01:18

Bioreactor Controls-II

In aerobic fermentations, oxygen is vital for microbial growth and metabolite production. Since air comprises only about 20% oxygen and the gas is poorly soluble in water—just 9 ppm at 20°C—supplying sufficient oxygen becomes a critical challenge, especially in high-demand processes like yeast growth or citric acid production. Even a fully saturated broth may offer only a few seconds of oxygen availability.To address this, sterile or scrubbed air is introduced into the...
76
Bioreactor Controls-III01:22

Bioreactor Controls-III

Strain improvement is a foundational strategy in industrial microbiology aimed at maximizing microbial productivity, particularly because natural isolates typically yield commercially valuable products in very low concentrations. Although optimizing the culture medium and environmental conditions can improve yields, these adjustments are inherently limited by the organism’s genetic potential. As a result, the focus shifts toward genetic modifications to enhance biosynthetic capacity. The...
67
Bioreactor Design and Operational System01:29

Bioreactor Design and Operational System

Bioreactors are engineered vessels designed to cultivate microorganisms under controlled conditions for industrial bioprocessing. They maintain sterility and allow precise regulation of pH, temperature, oxygen, and nutrient levels to optimize microbial growth and metabolite production. Bioreactors range from small laboratory units of 1 liter to industrial systems holding up to 500,000 liters, though only about 75% of their volume is actively used for fermentation. The remaining headspace...
198
Biofuels01:25

Biofuels

The microbial conversion of organic matter into biofuels holds potential as a renewable energy source. Among biofuel sources, microalgae are recognized as a highly efficient and adaptable feedstock for biodiesel production, owing to their rapid biomass accumulation, elevated lipid productivity, and capacity to proliferate in diverse aquatic systems, including freshwater, marine, and wastewater habitats. Unlike terrestrial crops, microalgae do not compete for land and can achieve significantly...
107
Scale-Up Processes01:14

Scale-Up Processes

The scale-up of microbial fermentation processes is essential in industrial biotechnology, allowing the transition from laboratory-scale experiments to commercial-scale production while aiming to maintain product yield and quality. This process requires meticulous adjustment of equipment design, process parameters, and contamination control strategies to accommodate increasing culture volumes.At the laboratory scale, cultures are typically maintained in 1 to 10-liter glass or autoclavable...
105