Related Experiment Video

Updated: Apr 28, 2026

Fabrication of High Contrast Gratings for the Spectrum Splitting Dispersive Element in a Concentrated Photovoltaic System
12:08

Fabrication of High Contrast Gratings for the Spectrum Splitting Dispersive Element in a Concentrated Photovoltaic System

Published on: July 18, 2015

10.0K

Spectrum splitting metrics and effect of filter characteristics on photovoltaic system performance

Juan M Russo, Deming Zhang, Michael Gordon

    Optics Express
    |June 13, 2014
    PubMed

    More Related Videos

    X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells10:16

    X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells

    Published on: August 20, 2019

    15.5K
    Indoor Experimental Assessment of the Efficiency and Irradiance Spot of the Achromatic Doublet on Glass ADG Fresnel Lens for Concentrating Photovoltaics09:00

    Indoor Experimental Assessment of the Efficiency and Irradiance Spot of the Achromatic Doublet on Glass ADG Fresnel Lens for Concentrating Photovoltaics

    Published on: October 27, 2017

    11.6K

    Related Concept Videos

    IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations01:08

    IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations

    Identical bonds within a polyatomic group can stretch symmetrically (in-phase) or asymmetrically (out-of-phase). Similar to hydrogen bonding, these vibrations also influence the shape of the IR peak. Generally, asymmetric stretching frequencies are higher than symmetric stretching frequencies. For example, primary amines exhibit two distinct IR peaks between 3300–3500 cm−1 corresponding to the symmetric and asymmetric N-H stretching, while secondary amines exhibit a single...
    2.0K
    UV–Vis Spectrometers01:14

    UV–Vis Spectrometers

    The absorbance of UV and visible (UV–visible) radiations is measured using a UV–visible spectrophotometer. Deuterium lamps, which emit UV radiation, and tungsten lamps, which produce radiation in the visible region, are used as light sources in UV–visible spectrophotometers. A monochromator or prism is used for diffraction grating, i.e., to split the incoming radiation into different wavelengths. A system of slits is used to focus the desired wavelength on the sample cell.
    4.0K
    Spectrophotometry: Introduction01:16

    Spectrophotometry: Introduction

    Spectrophotometry is the quantitative measurement of the absorption, reflection, diffraction, or transmission of electromagnetic radiation through a material as a function of the intensity and wavelength of the radiation. A spectrophotometer is a device used to measure the change in the radiation intensity caused by its interaction with the material.
    The essential components of a spectrophotometer include a source of electromagnetic radiation, a slot for placing a material to be analyzed, and a...
    8.4K
    Ultraviolet and Visible (UV–Vis) Spectroscopy: Overview01:02

    Ultraviolet and Visible (UV–Vis) Spectroscopy: Overview

    Ultraviolet–visible (UV–visible or UV–Vis) spectroscopy is an analytical technique that investigates the interaction between matter and UV–Vis light within the electromagnetic spectrum. This method is widely used for its versatility, simplicity, and relatively quick data acquisition, making it valuable for both qualitative and quantitative analysis. When UV–Vis radiation passes through a material,  molecules absorb light depending on the energy required for...
    7.7K
    IR Spectrometers01:25

    IR Spectrometers

    There are two main infrared (IR) spectrophotometers: dispersive IR spectrometers and Fourier transform infrared (FTIR) spectrometers. In a dispersive IR spectrometer, a beam of infrared radiation produced by a hot wire is divided into two parallel equal-intensity beams using mirrors. One beam passes through the sample, while another is a reference beam. The beams then move through the monochromator, which separates the radiations into a continuous spectrum of different frequencies. The...
    3.1K
    Power Factor Correction01:20

    Power Factor Correction

    The power transmission to a factory involves the transfer of apparent power, a combination of active and reactive power. The power factor measures how effectively electrical power is converted into useful work output. The ratio of the real power (KW) that does the work to the apparent power (KVA) supplied to the circuit.
    801