Related Experiment Video

Updated: Apr 25, 2026

Autonomous and Rechargeable Microneurostimulator Endoscopically Implantable into the Submucosa
08:17

Autonomous and Rechargeable Microneurostimulator Endoscopically Implantable into the Submucosa

Published on: September 27, 2018

8.1K

Simple BiCMOS CCCTA design and resistorless analog function realization

Worapong Tangsrirat1

  • 1Faculty of Engineering, King Mongkut's Institute of Technology Ladkrabang (KMITL), Ladkrabang, Bangkok 10520, Thailand.

Thescientificworldjournal
|August 19, 2014
PubMed

More Related Videos

A Method for Growing Bio-memristors from Slime Mold07:46

A Method for Growing Bio-memristors from Slime Mold

Published on: November 2, 2017

10.7K
Gene Digital Circuits Based on CRISPR-Cas Systems and Anti-CRISPR Proteins10:46

Gene Digital Circuits Based on CRISPR-Cas Systems and Anti-CRISPR Proteins

Published on: October 18, 2022

1.9K

Related Concept Videos

Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
1.8K
Combination Of Resistors01:18

Combination Of Resistors

Electrical devices in any circuit can be connected either by series or parallel connections. Additionally, circuits can be connected involving both of these connections, known as combination or complex circuits. As these circuits have complex resistor connections, it is necessary to identify different parts as either series or parallel connections, then the whole combination of series and parallel resistors can be reduced to a single equivalent resistance. With the known equivalent resistance...
4.2K
Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...
815
MOS Capacitor01:25

MOS Capacitor

A Metal-Oxide-Semiconductor (MOS) capacitor is a fundamental structure used extensively in semiconductor device technology, particularly in the fabrication of integrated circuits and MOSFETs (metal-oxide-semiconductor field-effect transistors). The MOS capacitor consists of three layers: a metal gate, a dielectric oxide, and a semiconductor substrate.
The metal gate is typically made from highly conductive materials such as aluminum or polysilicon. Beneath the metal gate lies a thin layer of...
1.8K
Applications of RC Circuits01:22

Applications of RC Circuits

A relaxation oscillator is one of the applications of RC circuits. A neon lamp relaxation oscillator comprises a capacitor, a resistor, a voltage source, and a lamp. The lamp acts like an open circuit, with infinite resistance until the potential difference across the lamp reaches a specific voltage. At that voltage, the lamp acts like a short circuit with zero resistance, and the capacitor discharges through the lamp, thus producing light. Once the capacitor is fully discharged through the...
5.0K
Resistors In Parallel01:23

Resistors In Parallel

Resistors are in parallel when one end of all the resistors are connected to a continuous wire of negligible resistance and the other end of all the resistors are also connected to one another through a continuous wire of negligible resistance. In the case of a parallel configuration, the potential drop across each resistor is the same. Current through each resistor can be found using Ohm’s law, I = V/R, where the voltage is constant across each resistor. The sum of the individual...
5.7K