Related Experiment Video

Updated: Apr 23, 2026

Measuring Local Tissue Strains in Tendons via Open-Source Digital Image Correlation
07:50

Measuring Local Tissue Strains in Tendons via Open-Source Digital Image Correlation

Published on: January 27, 2023

3.6K

Predicting work-related incidence of lateral and medial epicondylitis using the strain index

Z Joyce Fan1, Stephen Bao, Barbara A Silverstein

  • 1Washington Traffic Safety Commission, Olympia, Washington.

American Journal of Industrial Medicine
|September 23, 2014
PubMed
Abstract

Keywords:
epicondylitisincidenceoccupationprospective studystrain index

More Related Videos

Stereo-Imaging System DLT Calibration to Capture 3D In Situ Displacements of Stretched Peripheral Nerves06:26

Stereo-Imaging System DLT Calibration to Capture 3D In Situ Displacements of Stretched Peripheral Nerves

Published on: January 12, 2024

887
Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion09:32

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Published on: April 11, 2018

9.6K

Related Concept Videos

Measurements of Strain01:27

Measurements of Strain

Strain quantifies the deformation of a material under force, typically measured as normal strain, which represents the change in length when compared with the original length. Electrical strain gauges are used for enhanced accuracy. These devices consist of a conductive wire mounted on a paper backing that adheres to the material's surface. These gauges operate on the piezoresistive effect, where the wire's electrical resistance changes in response to mechanical deformation. The strain...
2.8K
Strain Energy01:13

Strain Energy

Strain energy is a fundamental concept in the field of materials science and structural engineering, describing the energy absorbed by a material or structure when it is deformed under load.
Consider a rod that is fixed at one end and subjected to an axial force at the free end. This axial force induces stress within the rod, leading to its elongation. As the axial force increases, so does the elongation of the rod, illustrating a direct relationship between the force applied and the resulting...
1.3K
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
6.3K
Stress-Strain Diagram01:10

Stress-Strain Diagram

A stress-strain diagram is a crucial tool that graphically displays a material's mechanical characteristics. This diagram is derived from a tensile test performed on a carefully prepared cylindrical specimen. The specimen has two gauge marks inscribed on its central part, and the distance between these marks is known as the gauge length. The cylindrical specimen is placed in a testing machine, which applies an increasing centric load. As this load grows, so does the gauge length. This...
6.8K
Strain-Energy Density01:20

Strain-Energy Density

Understanding the strain energy density in materials under axial load is crucial for evaluating their mechanical behavior and durability. When a rod is subjected to such a load, it elongates and stores energy, known as strain energy, as potential energy within the material. This energy is measured in terms of energy per unit volume.
In the elastic region of a material, the relationship between the stress and the strain is linear and follows Hooke's Law. The strain energy density in this region...
1.1K
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
812