Related Experiment Video

Updated: Apr 18, 2026

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators
09:23

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators

Published on: May 30, 2014

15.2K

Phase noise tolerance study in coherent optical circular QAM transmissions with Viterbi-Viterbi carrier phase

Sebastian Ortega Zafra, Xiaodan Pang, Gunnar Jacobsen

    Optics Express
    |January 22, 2015
    PubMed

    More Related Videos

    Quasi-light Storage for Optical Data Packets07:45

    Quasi-light Storage for Optical Data Packets

    Published on: February 6, 2014

    11.4K
    Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source12:19

    Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source

    Published on: April 4, 2017

    9.0K

    Related Concept Videos

    Time and frequency -Domain Interpretation of Phase-lag Control01:21

    Time and frequency -Domain Interpretation of Phase-lag Control

    Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
    Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any...
    453
    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    538
    Linear Approximation in Frequency Domain01:26

    Linear Approximation in Frequency Domain

    Linear systems are characterized by two main properties: superposition and homogeneity. Superposition allows the response to multiple inputs to be the sum of the responses to each individual input. Homogeneity ensures that scaling an input by a scalar results in the response being scaled by the same scalar.
    In contrast, nonlinear systems do not inherently possess these properties. However, for small deviations around an operating point, a nonlinear system can often be approximated as linear....
    457
    Propagation of Uncertainty from Random Error00:59

    Propagation of Uncertainty from Random Error

    An experiment often consists of more than a single step. In this case, measurements at each step give rise to uncertainty. Because the measurements occur in successive steps, the uncertainty in one step necessarily contributes to that in the subsequent step. As we perform statistical analysis on these types of experiments, we must learn to account for the propagation of uncertainty from one step to the next. The propagation of uncertainty depends on the type of arithmetic operation performed on...
    2.2K
    Linear Approximation in Time Domain01:21

    Linear Approximation in Time Domain

    Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
    For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
    431
    Propagation of Uncertainty from Systematic Error01:10

    Propagation of Uncertainty from Systematic Error

    The atomic mass of an element varies due to the relative ratio of its isotopes. A sample's relative proportion of oxygen isotopes influences its average atomic mass. For instance, if we were to measure the atomic mass of oxygen from a sample, the mass would be a weighted average of the isotopic masses of oxygen in that sample. Since a single sample is not likely to perfectly reflect the true atomic mass of oxygen for all the molecules of oxygen on Earth, the mass we obtain from this...
    1.6K